مهندسی سازه و ساخت

مهندسی سازه و ساخت

مطالعه عددی رفتار چرخه‌ای قاب‌های فولادی مجهز به میراگر Uشکل زاویه‌دار با پیکربندی جدید

نوع مقاله : علمی - پژوهشی

نویسندگان
1 دانشجوی کارشناسی ارشد، گروه مهندسی عمران، واحد کرمانشاه، دانشگاه آزاد اسلامی، کرمانشاه، ایران
2 استادیار گروه مهندسی عمران، واحد کرمانشاه، دانشگاه آزاد اسلامی، کرمانشاه، ایران
10.22065/jsce.2026.601214.4133
چکیده
استفاده از میراگرهای فلزی به‌عنوان سامانه‌های اتلاف انرژی، راهکاری مؤثر برای افزایش ظرفیت جذب انرژی و تمرکز تغییرشکل‌های غیرخطی در اجزای مشخص سازه است. در این پژوهش، رفتار چرخه‌ای قاب فولادی مجهز به میراگر زاویه‌دار Uشکل با پیکربندی جدید، تحت بارگذاری رفت‌وبرگشتی کنترل‌شده با جابه‌جایی، به‌صورت عددی بررسی شد. ابتدا مدل‌های اجزای محدود میراگر و قاب فولادی بر اساس نتایج آزمایشگاهی در نرم‌افزار آباکوس اعتبارسنجی شدند. سپس قاب اصلی دارای دو مجموعه مهاربند ضربدری در دهانه میانی مدل‌سازی شد و اثر تعداد میراگرها بر پاسخ چرخه‌ای سیستم مورد ارزیابی قرار گرفت. شاخص‌های بررسی شامل منحنی‌های هیسترزیس و پوش، مقاومت حداکثر، سختی الاستیک و مؤثر، انرژی مستهلک‌شده، نسبت میرایی ویسکوز معادل، توزیع تنش و کرنش پلاستیک و نیروی محوری ستون‌ها بود. نتایج نشان داد که با افزایش تعداد میراگرها، مقدار بیشینه نسبت میرایی ویسکوز معادل از حدود ۲۰ به ۲۷ درصد افزایش یافت. همچنین، بیشترین مقادیر این نسبت در محدوده حدود ۴۰ تا ۶۰ درصد مقاومت حداکثر مشاهده شد. تمرکز تنش و کرنش پلاستیک عمدتاً در نواحی میراگرها رخ داد که بیانگر مشارکت مؤثر این اجزا در پاسخ غیرخطی سیستم تحت شرایط بارگذاری بررسی‌شده است. نتایج حاضر بیانگر ویژگی‌های رفتار چرخه‌ای پیکربندی پیشنهادی بوده و ارزیابی عملکرد دینامیکی آن تحت تحریک واقعی زمین‌لرزه مستلزم بررسی‌های تکمیلی است.
کلیدواژه‌ها
موضوعات

عنوان مقاله English

Numerical Investigation of the Cyclic Behavior of Steel Frames Equipped with Angled U-Shaped Dampers in a Novel Configuration

نویسندگان English

nader Norozy 1
Reza Khaleghi 2
Mohammadreza Ghotb 2
Hamidreza Vaziri 2
1 M.Sc. in Structural Engineering, Department of Civil Engineering, Ker.C., Islamic Azad University, Kermanshah, Iran
2 Department of Civil Engineering, Ker.C., Islamic Azad University, Kermanshah, Iran
چکیده English

Metallic energy dissipation devices can enhance the cyclic energy dissipation capacity of steel frames by concentrating inelastic deformations in designated structural components. This study numerically investigates the cyclic behavior of a steel frame equipped with angled U-shaped dampers in a novel configuration under displacement-controlled cyclic loading. First, the finite element models of the damper and steel frame were validated against experimental results using ABAQUS. Subsequently, the proposed frame incorporating two sets of X-braces in the middle span was modeled, and the influence of the number of dampers on the cyclic response was evaluated. The assessment parameters included hysteresis and envelope curves, maximum strength, elastic and effective stiffness, dissipated energy, equivalent viscous damping ratio, stress and plastic strain distributions, and column axial forces. The results showed that increasing the number of dampers increased the maximum equivalent viscous damping ratio from approximately 20% to 27%. The highest damping ratios were observed within approximately 40–60% of the maximum strength. Stress and plastic strain were primarily concentrated in the dampers, indicating their contribution to the nonlinear response of the system under the considered loading conditions. These findings characterize the cyclic behavior of the proposed configuration, while evaluating its dynamic performance under earthquake ground motions requires further investigation.

کلیدواژه‌ها English

Steel frame
Angled U-shaped damper
Finite element analysis
Cyclic energy dissipation
Hysteretic response

مقالات آماده انتشار، پذیرفته شده
انتشار آنلاین از 29 آبان 1405

  • تاریخ دریافت 16 شهریور 1405
  • تاریخ بازنگری 24 آبان 1405
  • تاریخ پذیرش 29 آبان 1405