An investigation on mechanical and electrical properties and microstructure of Ultra-High Performance Concrete Containing Silica Fume and PVA Fiber

Document Type : Original Article

Authors

1 Department of Civil Engineering, Fouman and Shaft Branch, Islamic Azad University, Fouman, Iran

2 Civil engineering Dept, technical faculty, university of giulan

3 Department of Civil Enineering, Faculty of Engineering, University of Guilan, Rasht, IRan

4 Department of Civil Engineering, Faculty of Engineering, University of guilan, Rasht, Iran

Abstract

Ultra-high performance concrete (UHPC) is a new type of composite materials that can develop a compressive strength up to 200  MPa and high tensile strength around 10 MPa, given the low water-to-binder ratio (W/B). The fracture energy of UHPC can vary from 8560 to 40,000 J/m2, which is approximately 220 times greater than that of conventional mortar. Due to its superior properties, Ultra-high performance concrete has received great attention among researchers recently. Very high compressive strength leads to a significant weight loss of the structure and makes it possible to build slender structural elements. In this paper, the ultra-high performance fiber reinforced concrete specimens exposed to two different curing regimes, a 23°C limewater tank, and a 70°C hot-water tank. Then, the compressive and flexural strength and the electrical behavior of specimens were evaluated. Mechanical strength at the age of 28 days and six months were measured, in order to in conjunction with durability-related properties offer an overall view of UHPFRC characteristics. Results showed that the PVA fiber affected the mechanical strengths by preventing the propagation of cracks and by increasing the total porosity of the matrix. Moreover, its influence on resistivity was highly dependent on the concentration of silica fume particles.

Keywords

Main Subjects


[1] D.-Y. Yoo, N. Banthia, Mechanical properties of ultra-high-performance fiber-reinforced concrete: A review, Cement and Concrete Composites 73 (2016) 267-280
[2] J. Charron, E. Denarié, E. Brühwiler, Permeability of UHPFRC under high stresses, International RILEM Symposium on Concrete Science and Engineering: A Tribute to Arnon Bentur, RILEM Publications SARL, 2004.
[3] P. Richard, M. Cheyrezy, Reactive Powder Concrete with high ductility and 200-800 MPa compressive strength, Metha, PK (edition) Concrete Technology Past Present and Future, SP.
[4] M. Reda, N. Shrive, J. Gillott, Microstructural investigation of innovative UHPC, Cement and Concrete Research 29(3) (1999) 323-329
[5] T. Ahlborn, D. Harris, D. Misson, E. Peuse, Characterization of strength and durability of ultra-high-performance concrete under variable curing conditions, Transportation Research Record: Journal of the Transportation Research Board (2251) (2011) 68-75
[6] P. Richard, M. Cheyrezy, Composition of reactive powder concretes, Cement and concrete research 25(7) (1995) 1501-1511
[7] J.J. Park, S.T. Kang, K.T. Koh, S.W. Kim, Influence of the ingredients on the compressive strength of UHPC as a fundamental study to optimize the mixing proportion, Proceedings of the second international symposium on ultra high performance concrete, 2008, pp. 105-112.
[8] S. Zhao, J. Fan, W. Sun, Utilization of iron ore tailings as fine aggregate in ultra-high performance concrete, Construction and Building Materials 50 (2014) 540-548
[9] S.H. Park, D.J. Kim, G.S. Ryu, K.T. Koh, Tensile behavior of ultra high performance hybrid fiber reinforced concrete, Cement and Concrete Composites 34(2) (2012) 172-184
[10] K. Wille, S. El-Tawil, A. Naaman, Properties of strain hardening ultra high performance fiber reinforced concrete (UHP-FRC) under direct tensile loading, Cement and Concrete Composites 48 (2014) 53-66
[11] S.-T. Kang, J.-K. Kim, The relation between fiber orientation and tensile behavior in an Ultra High Performance Fiber Reinforced Cementitious Composites (UHPFRCC), Cement and Concrete Research 41(10) (2011) 1001-1014
[12] M.-J. Kim, D.-Y. Yoo, S. Kim, M. Shin, N. Banthia, Effects of fiber geometry and cryogenic condition on mechanical properties of ultra-high-performance fiber-reinforced concrete, Cement and Concrete Research 107 (2018) 30-40
[13] D.L. Nguyen, G.S. Ryu, K.T. Koh, D.J. Kim, Size and geometry dependent tensile behavior of ultra-high-performance fiber-reinforced concrete, Composites Part B: Engineering 58 (2014) 279-292
[14] D.-Y. Yoo, S.-T. Kang, Y.-S. Yoon, Enhancing the flexural performance of ultra-high-performance concrete using long steel fibers, Composite Structures 147 (2016) 220-230
[15] D.J. Kim, S.H. Park, G.S. Ryu, K.T. Koh, Comparative flexural behavior of hybrid ultra high performance fiber reinforced concrete with different macro fibers, Construction and Building Materials 25(11) (2011) 4144-4155
[16] F. Wenner, A method for measuring earth resistivity, Journal of the Washington Academy of Sciences 5(16) (1915) 561-563
[17] P. Gu, Z. Xu, P. Xie, J. Beaudoin, Application of AC impedance techniques in studies of porous cementitious materials:(I): influence of solid phase and pore solution on high frequency resistance, Cement and Concrete Research 23(3) (1993) 531-540
[18] Z. Xu, P. Gu, P. Xie, J. Beaudoin, Application of AC impedance techniques in studies of porous cementitious materials:(II): Relationship between ACIS Behavior and the Porous Microstructure, Cement and concrete research 23(4) (1993) 853-862
[19] W. McCarter, R. Brousseau, The AC response of hardened cement paste, Cement and Concrete Research 20(6) (1990) 891-900
[20] K. Brantervik, G. Niklasson, Circuit models for cement based materials obtained from impedance spectroscopy, Cement and concrete research 21(4) (1991) 496-508
[21] W. Morris, E. Moreno, A. Sagüés, Practical evaluation of resistivity of concrete in test cylinders using a Wenner array probe, Cement and concrete research 26(12) (1996) 1779-1787
[22] S. Millard, L. Sadowski, Novel method for linear polarisation resistance corrosion measurement, e-Journal of Nondestructive Testing & Ultrasonics 14 (2009) 
[23] S. Wen, D. Chung, The role of electronic and ionic conduction in the electrical conductivity of carbon fiber reinforced cement, Carbon 44(11) (2006) 2130-2138
[24] H. Li, H.-g. Xiao, J.-p. Ou, Effect of compressive strain on electrical resistivity of carbon black-filled cement-based composites, Cement and Concrete Composites 28(9) (2006) 824-828
[25] B. Chen, J. Liu, K. Wu, Electrical responses of carbon fiber reinforced cementitious composites to monotonic and cyclic loading, Cement and concrete research 35(11) (2005) 2183-2191
[26] S.P. Wu, L. Mo, Z. Shui, Piezoresistivity of graphite modified asphalt-based composites, Key Engineering Materials, Trans Tech Publ, 2003, pp. 391-396.
[27] S. Wen, D. Chung, Uniaxial tension in carbon fiber reinforced cement, sensed by electrical resistivity measurement in longitudinal and transverse directions, Cement and Concrete Research 30(8) (2000) 1289-1294
[28] F. Reza, G.B. Batson, J.A. Yamamuro, J.S. Lee, Resistance changes during compression of carbon fiber cement composites, Journal of Materials in Civil Engineering 15(5) (2003) 476-483
[29] H.V. Le, D.J. Kim, Effect of matrix cracking on electrical resistivity of high performance fiber reinforced cementitious composites in tension, Construction and Building Materials 156 (2017) 750-760
[30] D.L. Nguyen, J. Song, C. Manathamsombat, D.J. Kim, Comparative electromechanical damage-sensing behaviors of six strain-hardening steel fiber-reinforced cementitious composites under direct tension, Composites Part B: Engineering 69 (2015) 159-168
[31] R. Ranade, J. Zhang, J.P. Lynch, V.C. Li, Influence of micro-cracking on the composite resistivity of engineered cementitious composites, Cement and Concrete Research 58 (2014) 1-12
[32] A. C150, Standard specification for Portland cement, American Society for Testing and Materials:(ASTM) International West Conshohocken, PA, 2002.
[33] A. ASTM, Standard specification for silica fume used in cementitious mixtures,  (2011) 
[34] C. ASTM, Standard specification for chemical admixtures for concrete, Annual book of ASTM standards  (2013) 
[35] A.S.f. Testing, M.C.C.-o. Cement, Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (using 2-in. Or [50-mm] Cube Specimens), ASTM International2013.
[36] B. Chen, K. Wu, W. Yao, Conductivity of carbon fiber reinforced cement-based composites, Cement and Concrete Composites 26(4) (2004) 291-297
[37] J. Cao, D. Chung, Electric polarization and depolarization in cement-based materials, studied by apparent electrical resistance measurement, Cement and Concrete research 34(3) (2004) 481-485
[38] P. Xie, P. Gu, J.J. Beaudoin, Electrical percolation phenomena in cement composites containing conductive fibres, Journal of Materials Science 31(15) (1996) 4093-4097
[39] S. Wen, D. Chung, Electric polarization in carbon fiber-reinforced cement, Cement and Concrete Research 31(1) (2001) 141-147
[40] B. Han, X. Guan, J. Ou, Electrode design, measuring method and data acquisition system of carbon fiber cement paste piezoresistive sensors, Sensors and Actuators A: Physical 135(2) (2007) 360-369
[41] B. Han, S. Ding, X. Yu, Intrinsic self-sensing concrete and structures: A review, Measurement 59 (2015) 110-128
[42] A. ASTM, Standard test method for flexural strength of hydraulic-cement mortars,  (2008) 
[43] C. ASTM, 349-97. Standard test method for compressive strength of hydraulic-cement mortars (using portions of prisms broken in flexure), Annual book of ASTM 4 (2002) 
[44] N. Van Tuan, G. Ye, K. Van Breugel, O. Copuroglu, Hydration and microstructure of ultra high performance concrete incorporating rice husk ash, Cement and Concrete Research 41(11) (2011) 1104-1111
[45] C. Shi, Z. Wu, J. Xiao, D. Wang, Z. Huang, Z. Fang, A review on ultra high performance concrete: Part I. Raw materials and mixture design, Construction and Building Materials 101 (2015) 741-751
[46] N. Olsson, L.-O. Nilsson, M. Åhs, V. Baroghel-Bouny, Moisture transport and sorption in cement based materials containing slag or silica fume, Cement and Concrete Research 106 (2018) 23-32