[1] FEMA-350(2000) "Recommended Seismic Design Criteria for New Steel Moment-Frame Buildings, Prepared by SAC Joint Venture for the Federal Emergency Management Agency."Washington, DC.
[2] Ricles, J.M., Sause, R., Garlock, M. and C. Zhao. (2001).”Post-Tensioned Seismic Resistant Connections for Steel Frames,” Journal of Structural Engineering, ASCE, Vol. 127, No.2, pp 113-121.
[3] Ricles, J.M., Sause, R., Peng, S.W., and L.W. Lu. (2002).”Experimental Evaluation of Earthquake Resistant Post-Tensioned Steel Connections,” Journal of Structural Engineering, ASCE, Vol. 128, No. 7, pp. 850-859.
[4] Garlock M.M., Ricles J.M., Sause R. (2005). "Experimental Studies of Full-Scale Posttensioned Steel Connections", Journal of Structural Engineering, pp.438-448.
[5] Moradi, and M. Shahria Alam. (2015). "Finite-Element Simulation of Posttensioned Steel Connections with Bolted Angles under Cyclic Loading". This paper is part of the Journal of Structural Engineering, ASCE, ISSN 0733-9445/04015075(15)/$25.00.
[6] Gerami, Khatami. (May 2011). "Investigating the role of effective parameters in the behavior of steel post-tenshioned connections with upper and lower angles", 6th National Congress on Civil Engineering, Semnan University.
[7] Abedi Sarvestani, Rasti Ardakani, Shirvand. (2014). "Behavior of celf-centering post-tenshioned connections between beam and column includ angle with stiffner in steel moment resistant frame", 2nd International Congress on structure, Architecture and Urban Development, Tabriz University,iran.
[8]Sharbati, Hadian Fard, Lashkari.(2012). "Investigating the behavior of post-tensioned steel moment resisting frames connections, equipped with energy dissipation", 9th International Congress on Civil Engineering, Iran (Esfahan).
[9] Garlock M.M. (2002). "Full-Scale Testing ,Seismic Analysis,and Design of Post tensioned Seismic Resistant Connections for Steel Frames",PH.D. dissertation,Lehigh University.
[10] Gerami, Khatami. (2013). "Evaluation of the Seismic demand for post-tensioned moment resistant frame with Changes in Effective Parameters of post-tensioning", Scientific and Research Institute of Structural and Steel Research, Ninth, No 14.
[11] Rojas, P., Ricles, J.M. and Sause, R. (2005).“Seismic performance of posttensioned steel moment resisting frames with friction devices”, ASCE Journal of Structural Engineering, Vol. 131, No. 4, p. 529-540.
[12] Ricles, sause, wolski, c-y. Seo, and j. Iyama. (2006). "post tensioned moment connections with a bottom Flange friction device for seismic resistant selfcentering Steel Mrfs". 4th International Conference on Earthquake Engineering Taipei, Taiwan October 12-13.
[13] Ahmadi, Shadman, Amri.(2016). " Numerical Analysis of post-tensioned steel moment connections with bolted top-and-seat angle", Quarterly Journal of Structural Analysis - Earthquake Volume 13, No. 1.
[14]Abdollahzade, Hamidi, Asghari. (2016). " Numerical modeling of post-tensioned steel connection between beam and column under Cyclic loading", 4th. International Congress on Civil Engineering, Architecture and Urban Development, Shahid Beheshti University , Tehran , Iran, 27-29.
[15]Mohammadi, Inanlou. (2015). " Investigating the effective parameters in the behavior of post-tensioned cable connection in Progressive Failure", Tenth International Congress on Civil Engineering, Tabriz, Tabriz University of Civil Engineering.
[16]Pirmoz, A. and M.M. Liu. (2016). "Finite element modeling and capacity analysis of post-tensioned steel frames against progressive collapse", Engineering Structures. 126: p. 446-456.
[17]Abaqus Inc., Abaqus Analysis User's Manual, Version 6.16.
[18] Garlock M, Sause R, Ricles J. (2007). "Behavior and design of posttensioned steel frame systems", Journal of Structural Engineering, ASCE; 133(3): 389–99.