ORIGINAL_ARTICLE
ارائه رابطه کاهندگی تابع شدت اریاس در فلات ایران با استفاده از الگوریتم هوشمند توسعه ژنی
زلزله یکی از خطرهایی است که در طول سالیان گذشته تلفات و خسارات مالی زیادی بهجای گذاشته است. ایران نیز بهدلیل قرارگیری در یکی از مناطق لرزهخیز دنیا یعنی نوار آلپ-هیمالیا در معرض این خطرات واقع است. به همین دلیل مطالعات تحلیل خطر لرزهای در ایران از اهمیت خاصی برخوردار است. از ملزومات تحلیل خطر، استفاده از روابط کاهندگی پارامترهای لرزهای است. تابع شدت اریاس بعنوان یکی از پارامترهای مهم جنبش نیرومند زمین، در تجزیه و تحلیل خطر لرزهای استفاده میشود که به موجب آن میتوان پایداری شیبها در اثر زلزله را تخمین زد. هدف این پژوهش، ارائه رابطه کاهندگی تابع شدت اریاس در فلات ایران با استفاده از روشهای هوشمند میباشد. در این پژوهش از 1012 داده شتابنگاری استفاده شد. در ابتدا دادههایی که نیازمند فیلتر شدن بودن اصلاح گردیدند و سپس تمام دادهها مورد تجزیه و تحلیل قرار گرفتند. پارامترهایی از قبیل بزرگای زلزله، فاصله کانونی، سرعت موج برشی خاک و موقعیت جغرافیایی منطقه مورد نظر، بعنوان متغیر برای رابطه کاهندگی استفاده شد. بزرگای زلزله بزرگتر یا مساوی 4 در مقیاس بزرگای گشتاوری (Mw) در این تحقیق بکار گرفته شد. همچنین از نظر موقعیت جغرافیایی ایران به دو ناحیه البرز-ایران مرکزی و ناحیه زاگرس تقسیم شد. در نهایت الگوریتم توسعه ژنی (GEP) که نوعی الگوریتم هوشمند است، بعنوان روش رگرسیونگیری و محاسبه تابع هدف مورد استفاده قرار گرفت. مزیت این روش این است که در ابتدا الگویی برای تابع هدف مشخص نشده و الگو هم توسط روش هوشمند بصورت بهینه ارائه میگردد. تابع برازندگی نیز براساس ریشه حداقل مربعات خطا (RMSE) تعریف گردید. در نهایت رابطه کاهندگی براساس این تابع برازندگی محاسبه شد و نتایج مشاهده شده دارای ضریب تناسب بالا و برازندگی 867 از 1000 میباشد. همچنین رابطه ارائه شده در مقایسه با تحقیقات گذشته، مطابقت خوبی را نشان میدهد.
https://www.jsce.ir/article_86779_08e58b1aa2feefc468a00eead624523d.pdf
2021-04-21
5
24
10.22065/jsce.2019.156437.1719
رابطه کاهندگی
تابع شدت اریاس
الگوریتم توسعه ژنی
زاگرس
البرز- ایران مرکزی
علی
توسلیان
alitavassolian@shahroodut.ac.ir
1
دانشکده عمران،دانشگاه صنعتی شاهرود، شاهرود، ایران
AUTHOR
محمد
شامخی امیری
shamekhi@shahroodut.ac.ir
2
استادیار، دانشکده مهندسی عمران، دانشگاه صنعتی شاهرود، شاهرود، ایران
LEAD_AUTHOR
عطیه
اسحاقی
a.eshaghi@bhrc.ac.ir
3
مرکز تحقیقات راه، مسکن و شهرسازی، تهران، ایران
AUTHOR
[1] Satake, K. and Atwater, B.F. (2007). Long-Term Perspectives on Giant Earthquakes and Tsunamis at Subduction Zones. Annual Review of Earth and Planetary Sciences, Vol. 35, pp. 349–374.
1
[2] Hadian, A. and Zafarani, H. and Farjoodi, J. (2015). Investigation of Source Parameters of Roudbar-Manjil Earthquake Using Hybrid Simulation Method. Journal of Structural and Construction Eng., Vol. 2, No. 1. (in Persian)
2
[3] Zare, M. and Kamranzad, F. (2015), Seismic Distribution in Iran. Journal of Spatial Analysis Environmental Hazarts, Vol. 1, No. 4, pp.39-58. (in Persian)
3
[4] Kramer, S.L. (1996). Geotechnical Earthquake Engineering. Prentice-Hall Inc., New Jersey, p. 653.
4
[5] Somerville, P.G. and Graves, R.W. (2003). Characterization of earthquake strong ground motion. Pure Applied Geophysics, Vol. 160, pp.1811-1828.
5
[6] Bozorgnia, Y. and Bertero, V. (2004). Earthquake Engineering: From Engineering Seismology to Performance-Based Engineering. CRC Press, Boca Raton, FL, USA.
6
[7] Khademi, M.H. (2002). Attenuation of peak and spectral accelerations in the Persian plateau. In Proceedings of Twelfth European Conference on Earthquake Engineering, pp.330.
7
[8] Wilson, R.C. and Keefer, D.K. (1985). Predicting the areal limits of earthquake-induced landsliding. In: Ziony JI, editor. Evaluating earthquake hazards in the Los Angeles region an earth science perspective. US Geologica lSurvey, Professional Paper1360, pp. 45–316.
8
[9] Jibson, R.W. (1987). Summary of research on the effects of topographic amplification of earthquakes shaking on slope stability, US Geological Survey, Menlo Park, California, Open File Report 87-268.
9
[10] Sabetta, F. and Pugliese, A. (1996). Estimation of response spectra and simulation of nonstationary earthquake ground motions. Bulletin of the Seismological Society of America, Vol. 86, No. 2, pp.337–352.
10
[11] Hwang, H. and Lin, C.K. and Yeh, Y.T. and Cheng, S.N. and Chen, K.C. (2004). Attenuation relations of Arias intensity based on the Chi-Chi Taiwan earthquake data. Soil Dynamics and Earthquake Eng., Vol. 24, pp. 17–509.
11
[12] Travasarou, T. and Bray, J.D. and Abrahamson, N.A. (2003). Empirical attenuation relationship for Arias Intensity. Earthquake Eng. Structure Dynamics, Vol. 32, pp. 55–1133.
12
[13] Mahdavifar, M. and Jafari, M.K. and Zolfaghari, M.R. (2007). The attenuation of Arias Intensity in Alborz and Central Iran. In Proceedings of the fifth international conference on seismology and earthquake engineering, Tehran, Iran.
13
[14] Rajabi, A.M. and Khamehchiyan, M. and Mahdavifar, M. and DelGaudio, V. (2010). Attenuation relation of Arias intensity for Zagros Mountains region (Iran). Soil Dynamics and Earthquake Eng., Vol. 30, pp.110-118.
14
[15] Ghodrati Amiri, G. and zahedi, M. and Mahdavian, A. and Gholami, S. (2004). Appropriate frequency band for correcting for Iranian Accelerograms in diffrenet site conditions. Journal of Faculty of Eng., University of Tehran, Vol. 38, No. 2, pp. 231–249. (in Persian)
15
[16] Vice Presidency for Strategic Planning and Supervision, (2014). Guideline for Seismic Hazard Analysis, Code No.626. (in Persian)
16
[17] Ministry of Energy, (2000). History of Attenuation models and criteria for selecting appropriate models, Code No.134. (in Persian)
17
[18] Mirzaei, H. (2000). Geological Site Investigation on Some Accelerograph Stations in Iran through Geophysical Method. BHRC publication No. 324, Tehran, Iran. (in Persian)
18
[19] Road, Housing and Urban Development Research Center, (2014). Iranian Code of Practice for Seismic Resistant Design of Buildings, Standard No.2800, 4th Edition. (in Persian)
19
[20] Ghodrati Amiri, G. and Shamekhi Amiri, M. Namiarnian, P. and Emadzadeh, A. (2013). Attenuation relationship for inelastic earthquake spectra in Iran. Proceedings of the Institution of Civil Engineers.
20
[21] Ferreira, C. (2001). Gene expression programming: A new adaptive algorithm for solving problems. Vol. 13(2), pp. 87–129.
21
[22] Ferreira, C. (2006). “Gene expression programming: Mathematical modeling by an artificial intelligence. Springer-Verlag.
22
[23] Ghodrati Amiri, G. and Shamekhi Amiri, M. (2015). Attenuation relationships for peak ground acceleration in the Iranian plateau using Gene Expression Programming (GEP). Civil Engineering Sharif, Vol. 38, No. 2. (in Persian)
23
[24] Ghodrati Amiri, G. and Mahdavian, A. and Manouchehri Dana, F. (2007). Attenuation relationships for Iran. Journal of Earthquake Eng., Vol. 11, No. 4, pp. 469-492.
24
ORIGINAL_ARTICLE
مطالعه مقاومت فشاری، نفوذپذیری و خوردگی میلگردها در نمونههای بتنی حاوی پوزولانهای دوده سیلیسی، خاکستر بادی و زئولیت
بتن مسلح متداولترین مصالح در ساخت و ساز است. دوام بتن مسلح، عمدتاً به شرایط قرارگیری و محیط اطراف آن همچون کربناته شدن، خوردگی، انجماد و ذوب شدن بستگی دارد. خوردگی فولاد در بتن، یکی از دلایل عمده زوال زودرس سازههای بتنی مسلح میباشد که منجر به خرابی سازهای میگردد و به مقدار قابل توجهی تحت تأثیر نفوذپذیری پوشش بتنی میباشد که آرماتورها را در برابر خوردگی حفظ میکند. ازاینرو، در این تحقیق اثر پوزولانهای دوده سیلیسی، خاکستر بادی و زئولیت بر مقاومت فشاری، نفوذپذیری و خوردگی میلگردها مورد ارزیابی قرار گرفته است. نتایج مقاومت فشاری نمونههای 7 و 28 روزه نشان میدهد که دوده سیلیسی موجب افزایش مقاومت فشاری نسبت به نمونه کنترل (فاقد پوزولان) شده است. جز برای نمونههای حاوی زئولیت در درصدهای وزنی جایگزینی برابر با 5، 10 و 15 درصد و خاکستر بادی در درصد وزنی برابر با 5 درصد، در سایر موارد مقاومت فشاری نمونههای 28 روزه حاوی خاکستر بادی و زئولیت نسبت به مقاومت فشاری نمونه کنترل کمتر است. نتایج آزمایش ”محفظه استوانهای“ نیز بیانگر کاهش نفوذپذیری نمونههای 7 روزه حاوی این پوزولانها نسبت به نمونه کنترل میباشد. همچنین بر اساس نتایج روش نیمپیل، مقاومت نمونههای بتنی مسلح حاوی دوده سیلیسی و زئولیت در برابر خوردگی در اثر استفاده از این پوزولانها بهبود یافته است.
https://www.jsce.ir/article_86849_afe0e07fa14c2d73aa441b134e80bd40.pdf
2021-04-21
25
43
10.22065/jsce.2019.154574.1697
نفوذپذیری
دوده سیلیسی
زئولیت
خاکستر بادی
روش محفظه استوانهای
خوردگی آرماتورها
روش نیمپیل
محمود
نادری
naderi-m@ikiu.ac.ir
1
استاد، دانشکده فنی و مهندسی، دانشگاه بین المللی امام خمینی (ره)، قزوین، ایران
LEAD_AUTHOR
علیرضا
کبودان
alireza.kaboudan@yahoo.com
2
گروه عمران، دانشکده فنی و مهندسی، دانشگاه بین المللی امام خمینی (ره)، قزوین، ایران
AUTHOR
کیمیا
کارگرفرد
kimiya_kargarfard@yahoo.com
3
گروه عمران، دانشکده فنی و مهندسی، دانشگاه بین المللی امام خمینی (ره)، قزوین، ایران
AUTHOR
[1] ACI Committee. (2001), Protection of Metals in Concrete against Corrosion (ACI 222-01), American Concrete Institute, Farmington Hills, MI.
1
[2] Brown, M.C. (2002), Corrosion protection service life of epoxy coated reinforcing steel in Virginia Bridge Decks. Ph.D Thesis, faculty of the Virginia polytechnic Institute and state university.
2
[3] Verma, S.K., Bhadauria, S.S. and Akhtar, S. (2014). Monitoring corrosion of steel bars in reinforced concrete structure. The scientific world journal, pp.1–9.
3
[4] Castel, A., Khan, I. and Gilbert, R.I. (2015). Development Length in Reinforced Concrete Structures Exposed to Steel Corrosion: A Correction Factor for AS3600 Provisions. Australian Journal of Structural Engineering, 16 (2), pp. 89–98.
4
[5] Otieno, M., Beushausen, H. and Alexander, M. (2011). Prediction of corrosion rate in RC Structures - A critical review. Modelling of Corroding Concrete Structures, pp.15–37
5
[6] Yuan, Y., Ji, Y. and Jiang, J. [2009]. Effect of corrosion layer of steel bar in concrete on time-variant corrosion rate. Materials and Structures, 42(10), pp.1443–1450.
6
[7] Masadeh, S. (2015). Performance of Galvanized Steel Reinforcement in Concrete in Sea and Dead Sea Water. Journal of Materials Science and Chemical Engineering, 3(5), pp. 46–53.
7
[8] Masadeh, S. (2015). The Effect of Added Carbon Black to Concrete Mix on Corrosion of Steel in Concrete. Journal of Materials Science and Chemical Engineering, 3(4), pp. 271–276.
8
[9] Petersen, R.B. and Melchers, R.E. (2012). Long –term corrosion of cast iron cement lined pipes. Proceedings of corrosion and prevention, 23, pp. 1–10
9
[10] ASTMC 618-99a. (1999). Standard Specification for Coal Fly Ash and Raw or Calcined Natural Pozzolan for Use in Concret, ASTM International, West Conshohocken, PA.
10
[11] Hossain, K. M. A. (2004). Chloride induced corrosion of reinforcement in volcanic ash and pumice based blended concrete. Cement and Concrete Composites, 39 (2), pp 201–210
11
[12] Hossain, K. M. A., and Lachemi, M. (2003). Corrosion resistance and Chloride diffusivity of volcanic ash blended cement mortar. Cement and Concrete Composites, 34 (4), pp. 695–702.
12
[13] Shah, S.P. and Ahmad, S.H. (1994). High performance concrete. Properties and applications. New York: McGraw-Hill
13
[14] Detwiler, R. J., Bhatty, J. I. and Bhattacharja, S. (1996). Supplementary Cementing Materials for Use in Blended Cements. Skokie: Portland Cement Association
14
[15] Kjellsen, K. O., Wallevik, O. H. and Hallgren, M. (1999). On the compressive strength development of high performance concrete and paste - effect of silica fume. Materials and Structures, 32 (1), pp. 63-69.
15
[16] Diab, A.M., Awad, A.E.M., Elyamany, H.E. and Elmoaty, A.E.M.A. (2012). Guidelines in compressive strength assessment of concrete modified with silica fume due to magnesium sulfate attack. Construction and Building Materials, 36. pp 311–318.
16
[17] Massazza, F. (1998). Pozzolana and pozzolanic cements. Lea’s chemistry of cement and concrete, 4th ed, pp 471–631.
17
[18] Shi, H.S., Xu, B.W. and Zhou, X.C. (2009). Influence of mineral admixtures on compressive strength, gas permeability and carbonation of high performance concrete. Constr Build Mater. 23 (5), pp 1980–1985.
18
[19] Najimi, M. (2010). Investigating the properties of concrete containing natural zeolite as supplementary cementitious materials, Building and Housing Research Center, Tehran
19
[20] Canpolat, F., Yılmaz, K., Köse, M.M., Sümer, M. and Yurdusev, M.A. (2004). Use of zeolite, coal bottom ash and fly ash as replacement materials in cement production. Cement and Concrete Research, 34 (5), pp 731–735.
20
[21] Poon, C.S., Lam, L., Kou, S.C. and Lin, Z.S. (1999). A study on the hydration rate of natural Zeolitee blended cement pastes. Construction and Building Materials, 13 (8), pp 427–432.
21
[22] Bilodeau, A., Sivasundaram, V., Painter, K.E. and Malhotra, V.M. (1994). Durability of concrete incorporating high volumes of fly ash from sources in US. ACI Mater. J., 91 (1), 3–12.
22
[23] Joshi, R.C. and Lohita, R.P. (1997). Fly ash in concrete: production, properties and uses. Amsterdam: Gordon and Breach.
23
[24] Han, S.H., Kim, J.K. and Park. Y. D. (2003). Prediction of compressive strength of fly ash concrete. Cement and Concrete Research, 33 (7), pp 965–971.
24
[25] Oner, A., Akyuz, S. and Yildiz, R. (2005). An Experimental Study on Strength Development of Concrete Containing Fly Ash and Optimum Usage of Fly Ash in Concrete, Cement and Concrete Research, 35 (6), pp 1165–1171.
25
[26] Poon, C.S., Lam, L. and Wong, Y.L. (2000). A study on high strength concrete prepared with large volumes of low calcium fly ash. Cement and Concrete Research, 30 (3), pp 447–455.
26
[27] Neville, A.M. (1995). Properties of concrete. London: Longman.
27
[28] Chahal, N. and Siddique, R. (2013). Permeation properties of concrete made with fly ash and silica fume: Influence of ureolytic bacteria. Construction and Building Materials, 49, pp 161–174.
28
[29] Naderi, M. (2010). Determine of concrete, stone, mortar, brick and other construction materials permeability with cylindrical chamber method. Registration of Patent in Companies and industrial property Office. Reg. N. 67726. Iran.
29
[30] ASTM C876. (1991) "Standard test method for half-cell potentials of uncoated reinforcing steel in concrete".
30
[31] Ramachandran, V. S. and Beaudoin, J. J. (1999). Hand book of analytical techniques in concrete science and technology. institute for research in construction national research council Canada, Ottawa, Ontario, Canada.
31
[32] NORDTEST Project. (2002). Calibration of the electrochemical methods for the corrosion rate measurement of steel in concrete, SP Swedish National.
32
[33] ASTM C642-06. (2006). Standard Test Method for Density, Absorption, and Voids in Hardened Concrete. ASTM International, West Conshohocken, PA.
33
[34] ASTM C136-06. (2006). Standard Test Method for Sieve Analysis of Fine and Coarse Aggregates, ASTM International, West Conshohocken, PA.
34
[35] Trejo, D. and Halmer, C. (2009). Corrosion Performance tests for reinforcing steel in concrete: test procedures. Report No: FHWA/Tx-09/04825-P1, Texas Transportation Institute, Texas A & M University System.
35
[36] Canpolat, F., Yılmaz, K., Köse, M.M., Sümer, M. and Yurdusev, M.A. (2004). Use of zeolite, coal bottom ash and fly ash as replacement materials in cement production, Cement and Concrete Research, 34 (5), pp 731–735.
36
[37] Vejmelková, E., Ondráček, M. and Černý, R. (2012). Mechanical and Hydric Properties of High-Performance Concrete Containing Natural Zeolites. World Academy of Science, Engineering and Technology, International Journal of Chemical, Molecular, Nuclear, Materials and Metallurgical Engineering, 6 (3), pp 186–189.
37
[38] Sreeharsha, N. and Ramana, K. V. (2016). Study On the Strength Characteristics of Concrete with Partial Replacement of Cement by Zeolite and Metakaolin. International Journal of Innovative Research in Science, Engineering and Technology, 5 (12), pp 20363–20371.
38
[39] Ajileye, F.V. (2012). Investigations on microsilica (Silica Fume) as partial cement replacement in concrete. Global Journal of Research In Engineering, 12 (1), pp 17–23.
39
[40] Muhit, I.B., Ahmed, S.S., Amin, M.M. and Raihan, M.T. (2013). Effects of silica fume and fly ash as partial replacement of cement on water permeability and strength of high performance concrete. In: 4th International Conference on Advances in Civil Engineering, Delhi: IDES Conference Publishing System, pp 108–115.
40
[41] Kazemi., M.A., Baig, M. A. and Hesamuddin, M. (2015). Investigations on Micro Silica (Silica Fume) as Partial Replacement of Cement in Concrete. International Journal of Science and Research, 6 (4). pp 2273–2277.
41
[42] Marthong, C., Agrawal, T.P. and Marthong, C., (2012). Effect of fly ash additive on concrete properties. International Journal of Engineering Research and Applications, 2 (4), pp 1986–1991.
42
[43] Joshi, R. (2017). Effect on Compressive Strength of Concrete by Partial Replacement of Cement with Fly ash. International Research Journal of Engineering and Technology, 4 (2), pp 315–318.
43
[44] Saha, A.K. (2018). Effect of class F fly ash on the durability properties of concrete. Sustainable environment research, 28 (1), pp 25–31.
44
[45] Ahmadi, B. and Shekarchi, M. (2010). Use of natural zeolite as a supplementary cementitious material. Cement and Concrete Composites, 32(2), pp 134–141.
45
[46] Mittal, T., Borsaikia, A. and Talukdar, S. (2013). Effect of silica fume on some properties of concrete. In: International Conference on Structural Engineering Construction and Management. Kandy, pp 1–7.
46
[47] Hustad, T., Løland, K.E. and Gjørv, O.E. (1989). Effect of Condensed Silica Fume on the Permeability of Concrete. In: Third International Conference on Fly Ash, Silica Fume, Slag and Natural Pozzolans in Concrete, Malhotra: American Concrete, pp 307–319.
47
[48] Islam, M.M. and Islam, M.S. (2013). Strength and durability characteristics of concrete made with fly-ash blended cement. Australian Journal of Structural Engineering, 14 (3), pp 303–319.
48
[49] Dotto, J.M.R., De Abreu, A.G., Dal Molin, D.C.C. and Müller, I.L. (2004). Influence of silica fume addition on concretes physical properties and on corrosion behaviour of reinforcement bars. Cement and concrete composites, 26 (1), pp 31–39.
49
[50] Hou, J. and Chung, D.D.L. (2000). Effect of admixtures in concrete on the corrosion resistance of steel reinforced concrete. Corrosion Science, 42 (9), pp 1489–1507.
50
[51] Nooman, M.T. (2016).Effect of Zeolite Inclusion on Some Properties of Concrete and Corrosion Rate of Reinforcing Steel Bars Imbedded in Concrete. Journal of Mechanical and Civil Engineering, 13 (6), pp 51–59.
51
[52] Najimi, M., Sobhani, J., Ahmadi, B. and Shekarchi, M. (2012). An experimental study on durability properties of concrete containing zeolite as a highly reactive natural pozzolan. Construction and Building Materials, 35, pp 1023–1033.
52
ORIGINAL_ARTICLE
پهنهبندی نقاط مناسب برای اسکان موقت بعد از رخداد زلزله در شهر کرج با استفاده از تئوری منطق فازی
یکی از اقدامهای مهم بعد از رخداد زلزله، انتقال ساکنین به نقاط اسکان موقت میباشد. این نقاط، مناطقی از شهر هستند که از ضریب ایمنی بالاتری در برابر رخداد مجدد زلزله برخوردار بوده، دسترسی مناسبی به مراکز مدیریتی و امدادی دارند و با توجه به شرایط بحرانی منطقه بعد از رخداد زلزلهی اصلی، با انتقال سکنهی شهر به این مناطق، عملیات امدادرسانی با بیشترین سرعت و کمترین خطر قابل انجام خواهد بود. هدف از مطالعهی حاضر، تعیین نقاط مناسب برای احداث مکانهایی بهمنظور اسکان موقت آسیبدیدگان بعد از رخداد زلزله در شهر کرج است. برای این منظور، ابتدا معیارهای موثر در انتخاب محلهای مناسب برای اسکان موقت، شناسایی و به دو گروه معیارهای اصلی سازگار و ناسازگار، و دوازده زیرمعیار تقسیم میگردند. باتوجه به ماهیت تعیین مکانی مساله و نیز با در نظر داشتن تعداد پارامترهای موثر در تصمیمگیری، از تلفیق سیستم پردازش اطلاعات مکانی و منطق فازی، بههمراه روشهای تصمیمگیری چند معیاره، جهت تعیین مناسبترین نقاط استفاده میشود. بعد از فازیسازی معیارها، وزن دهی و اولویت بندی آنها با کمک روش تحلیل سلسله مراتبی فازی انجام، و نقشهی مطلوبیت منطقه نسبت به هر کدام از معیارها تهیه میگردد. نهایتا با تلفیق تاثیر معیارهای مطالعه شده با یکدیگر، نقشهی مطلوبیت منطقه نسبت به نقاط مناسب برای اسکان موقت، ارائه میگردد. از روی این نقشه، 7 نقطه بهعنوان نقاط مناسب برای احداث کمپ اسکان موقت انتخاب و با انجام تحلیل سلسله مراتبی با کمک نرمافزار Expert Choice، بهینهترین نقطه انتخاب میگردد.
https://www.jsce.ir/article_86851_e763372156b7d2a7f7965016fe3a6e2b.pdf
2021-04-21
44
55
10.22065/jsce.2019.156425.1709
نقاط بهینهی اسکان موقت
نرمافزار ArcGIS
نرم افزار Expert Choice
تحلیل سلسله مراتبی فازی
شهر کرج
آزاده
قدیمی حمزه کلایی
azd.ghadimi@gmail.com
1
دانشجوی دکترا، دانشکدهی محیط زیست و انرژی، دانشگاه آزاد اسلامی، واحد علوم و تحقیقات، تهران، ایران
AUTHOR
علیرضا
وفایی نژاد
a_vafaei@sbu.ac.ir
2
استادیار، دانشکدهی مهندسی عمران، آب و محیط زیست، دانشگاه شهید بهشتی، تهران، ایران
LEAD_AUTHOR
غلامرضا
قدرتی امیری
ghodrati@iust.ac.ir
3
استاد، دانشکدهی مهندسی عمران، دانشگاه علم و صنعت ایران، تهران، ایران
AUTHOR
[1] Zangiabadei, A., Mohamadei, G., Safaei, H., Gaedrahmati, S. (2008). Vulnerability indicators assessment of urban housing against the earthquake hazard; case study: Isfahan housing. Geography and Development Iranian Journal, 6 (12), 61-79. (in Persian)
1
[2] Hashemi, M., Alesheikh, A.A. (2011). A GIS-based earthquake damage assessment and settlement methodology. Soil Dynamics and Earthquake Engineering, 31, 1607-1617.
2
[3] Sinha, N., Priyanka, N., Joshi, P.K. (2016). Using Spatial Multi-Criteria Analysis and Ranking Tool (SMART) in earthquake risk assessment: a case study of Delhi region, India. Geomatics, Natural Hazards and Risk, 7 (2), 680-701.
3
[4] Sadrykia, M., Delavar, M.R., Zare, M. (2017). A GIS-based Fuzzy decision making model for seismic vulnerability assessment in areas with incomplete data. International Journal of Geo-Information, 6 (119), DOI: 10.3390/ijgi6040119.
4
[5] Ahmad, R.A., Singh, R. P., Adris, A. (2017). Seismic hazard assessment of Syria using seismicity, DEM, slope, active faults and GIS. Remote Sensing Applications: Society and Environment, 6, 59-70.
5
[6] Ghadimi Hamzehkolaei, A., Ghodrati Amiri, G., Gharagozlu, A., Vafaeinezhad, A., Zare Hosseinzadeh, A. (2018). Seismic zoning of urban areas considering the effect of physical conditions using Fuzzy logic theory: case study of Tehran’s 7th region. Journal of Structural and Construction Engineering, 5 (special 3), 5-15. (in Persian)
6
[7] Deligiannakis, G., Papanikolaou, I.D., Roberts, G. (2018). Fault specific GIS based seismic hazard maps for the Attica region, Greece. Geomorphology, 306, 264-282.
7
[8] Armas, I., Ionescu, R., Gavris, A., Toma-Danila, D. (2016). Identifying seismic vulnerability hotspots in Bucharest. Applied Geography, 77, 49-63.
8
[9] Pourahmad, A., Habibi, K., Zahraei, S., Nazari Adli, S. (2007). Utilizing Fuzzy algorithm and GIS to locate the urban equipment. Journal of Environmental Studies, 33 (42), 31-42. (in Persian)
9
[10] Hu, F., Xu, W., Li, X. (2012) A modified particle swarm optimization algorithm for optimal allocation of earthquake emergency shelters. International Journal of Geographical Information Science, 26 (9), 1643-1666, DOI: 10.1080/13658816.2011.643802.
10
[11] Stewart, T.J., Janssen, R. (2014). A multiobjective GIS-based land use planning algorithm. Computers Environment and Urban Systems, 46, 25-34.
11
[12] Esmaelian, M., Tavana, M., Arteaga, F.J.S., Mohammadi, S. (2015). A multicriteria spatial decision support system for solving emergency service station location problems. International Journal of Geographical Information Science, 29 (7), 1187-1213.
12
[13] Kaveh, A., Ghobadi, M. (2017). A multistage algorithm for blood banking supply chain allocation problem. International Journal of Civil Engineering, 15 (1), 103-112.
13
[14] Ma, C., Zhou, M. (2018). A GIS-based interval Fuzzy linear programming for optimal land resource allocation at a city scale. Social Indicators Research, 135 (1), 143-166. [15] Iranian Statistics Center, General Results of Population and Housing Census (2006), (in Persian).
14
[16] Organization of Housing and Urban Development of Alborz Province, Detailed Maps of Karaj Township (2006), (in Persian).
15
[17] Google Map, 2018.
16
ORIGINAL_ARTICLE
مدلسازی و بررسی رفتار ستونهای مرکب فولادی بتنی دوجداره با جداره داخلی دایره ای و جداره خارجی شش ضلعی
نوع جدیدی از ستونهای پر شده با بتن به صورت دوجداره مزیتهای بهتری در ساخت پایه های پل و ساختمانهای خاص از جمله چگونگی اتصال چندین تیر( حداکثر 6 تیر) به ستون مورد نظر واقع در مرکز ساختمان دارد. در این پژوهش به شبیهسازی 27 نمونه ستون مرکب دوجداره فولادی با جدارهی داخلی دایرهای و جدارهی خارجی شش ضلعی، به روش اجزای محدود و به کمک نرم افزار آباکوس پرداخته شده است. اثر تعدادی از پارامترهای موثر در رفتار ستونهای مرکب شامل: ارتفاع ستون، نسبت بعد به ضخامت جدارهی فولادی خارجی، نسبت قطر به ضخامت جدارهی فولادی داخلی و برون محوری در نظر گرفته شد. بارگذاری اعمالی به هر یک از نمونهها بهصورت محوری فشاری و بهصورت کنترل جابجایی انجام گرفت. نتایج حاصل شده از پارامترهای مورد بررسی نشان داد که با وجود اینکه در آییننامههای مختلف وقتی که نسبت برون محوری به قطر افزایش مییابد از میزان محصور شدگی کم می گردد، اما در مقاطع دولایه زمانی که این محدوده در بین فضای دو لوله قرار گیرد به دلیل فشار لوله داخلی به بتن، میزان محصور شدگی را حفظ می کند. همچنین درصد افزایش مقاومت سازه وابسته به ارتفاع سازه و برون محوری و نسبت بعد به ضخامت خارجی می باشد. میزان کاهش مقاومت نهایی محوری سازه با افزایش نسبی 50 درصدی در ارتفاع ستون و نسبت قطر به ضخامت ثابت، کاهشی بین 1 تا 15 درصد را به همراه دارد. با ثابت ماندن نسبت قطر به ضخامت داخلی و برون محوری و ارتفاع، تاثیر نسبت بعد به ضخامت خارجی بسیار بیشتر از سه پارامتر دیگر می باشد. با ثابت ماندن ارتفاع و افزایش نسبت بعد به ضخامت خارجی مود چروک شدگی نیز در ستون دولایه ایجاد شده است
https://www.jsce.ir/article_86852_4fb24c1aad8cc49d88b5c1815d7921b1.pdf
2021-04-21
56
69
10.22065/jsce.2019.160790.1732
ستون دوجداره مرکب
جداره فولادی شش ضلعی
اثر محصورشدگی
ظرفیت باربری نهایی
مدلسازی عددی
مرتضی
نقی پور
m-naghi@nit.ac.ir
1
استاد، دانشکده مهندسی عمران، دانشگاه صنعتی نوشیروانی بابل، بابل، ایران
LEAD_AUTHOR
سیده مائده
مهدوی شلمانی
maedeh-mahdavi@yahoo.com
2
کارشناس ارشد مهندسی سازه، دانشکده فنی و مهندسی، دانشگاه شمال، آمل، ایران
AUTHOR
صالح
محمد ابراهیم زاده
ebrahimzadeh@snit.ac.ir
3
دانشجوی دکترای مهندسی سازه، دانشگاه صنعتی نوشیروانی بابل، بابل، ایران
AUTHOR
[1] Mandal, A. (2010). Concrete Filled Steel Tube under Axial Compression. LAP LAMBERT Academic publishing, 96 pages.
1
[2] Hassanein, M.F. and Kharoob, O.F. (2014). Analysis of circular concrete-filled double skin tubular slender columns with external stainless steel tubes. Journal of Thin-Walled Structures, 79, 23-37.
2
[3] Yuan, W.b. and Yang, J.J. (2013). Experimental and numerical studies of short concrete-filled double skin composite tube columns under axially compressive loads. Journal of Constructional Steel Research, 80, 23-31.
3
[4] Ho, J.C.M. and Dong, C.X. (2014). Improving strength, stiffness and ductility of CFDST columns by external confinement. Journal of Thin-Walled Structures, 75, 18-29.
4
[5] Romero, M.L. Ibañez, C. Espinos, A. Portolés, J.M. and Hospitaler, A. (2017). Influence of Ultra-high Strength Concrete on Circular Concrete-filled Dual Steel Columns. Journal of Structures, 9, 13-20.
5
[6] Li, W. Han, L.H. and Zhao, X.L. (2012). Axial strength of concrete-filled double skin steel tubular (CFDST) columns with preload on steel tubes. Journal of Thin-Walled Structures, 56, 9-20.
6
[7] Li, W. Han, L.H. Ren, Q.X. and Zhao, X.L. (2013). Behaviour and calculation of tapered CFDST columns under eccentric compression. Journal of Constructional Steel Research, 83, 127-136.
7
[8] Li, W. Han, L.H. and Chan, T.M. (2014). Tensile behavior of concrete-filled double-skin steel tubular members. Journal of Constructional Steel Research, 99, 35-46.
8
[9] Pagoulatou, M. Sheehan, T. Dai, X.H. and Lam, D. (2014). Finite element analysis on the capacity of circular concrete-filled double-skin steel tubular (CFDST) stub columns. Journal of Engineering Structures, 72, 102-112.
9
[10] Uenaka, K. (2016). CFDST stub columns having outer circular and inner square sections under compression. Journal of Constructional Steel Research, 120, 1-7.
10
[11] خراسانی، ف؛ گرامی، م؛ خیرالدین، ع. (1396). مقایسه رفتار قابهای خمشی مرکب (RCS) و فولادی تحت زلزلههای حوزه نزدیک گسل. فصلنامه سازه و ساخت.
11
[12] حقیقت، آ؛ حیدریان، ن؛ شربتدار، م. (1396). بررسی اتصال خمشی ترکیبی نوین تحت بارگذاری چرخه ای و اثر آن در قاب مرکب یک طبقه. فصلنامه سازه و ساخت. دوره 4، شماره 2، تابستان 1396، صفحه 85-105.
12
[13] Ibañez, C., Romero, M. L., Espinós, A., Portolés, J. M., & Albero, V. (2017, November). Ultra-high strength concrete on eccentrically loaded slender circular concrete-filled dual steel columns. In Structures (Vol. 12, pp. 64-74). Elsevier.
13
ORIGINAL_ARTICLE
بررسی اثر آب به سیمان و حجم الیاف فولادی در پارامترهای شکست بتن خودمتراکم حاوی الیاف فولادی
در این تحقیق اثر نسبت اب به سیمان و درصد حجمی الیاف فولادی بر روی پارامترهای شکست بتن خو متراکم به دو روش کار شکست و اثر اندازه مورد بررسی قرار گرفته است. در یک برنامه ازمایشگاهی نسبت آب به سیمان و درصد حجمی الیاف فولادی متغییر در نظر گرفته شده ، بدین منظور 5 طرح اختلاط در 2 سری ساخته شده است که در سری اول نسبت اب به سیمان متغییر (شامل مقادیر 42/0 ، 52/0 و62/0 )و درصد الیاف فولادی مقدار ثابت 3/0 درصد در نظر گرفته شده و در سری دوم درصد الیاف فولادی متغییر ( شامل 1/0 ، 3/0 و 5/0 درصد )و نسبت اب به سیمان مقدار ثابت 52/0 در نظر گرفته شده است. نتایج نشان می دهد که با افزایش نسبت آب به سیمان انرژی شکست کاهش و بتن تردتر میشود هر چند که در نسبت آب به سیمان کمتر شاهد رفتار متفاوتی می باشیم و همچنین با افزایش درصد الیاف فولادی انرژی شکست افزیش و بتن شکل پذیر تر می گردد، همچنین نتایج نشان می دهد افزایش در صد الیاف فولادی می تواند در کاهش اثر اندازه موثر باشد. انرژی شکست در روش کار شکست نسبت به روش اثر اندازه مقدار بیشتری دارد و نسبت GF/Gf برای تمام طرح اختلاط ها محاسبه شده است.
https://www.jsce.ir/article_86853_066870494e948891499b008e77a720ed.pdf
2021-04-21
70
86
10.22065/jsce.2019.161671.1745
بتن الیافی
انرژی شکست
الیاف فولادی
بتن خود متراکم
اثر اندازه
محمد
قاسمی
m.ghasemi@velayat.ac.ir
1
دانشجوی دکتری سازه، دانشکده مهندسی شهید نیکبخت ، دانشگاه سیستان و بلوچستان، زاهدان، ایران
AUTHOR
محمد رضا
قاسمی
mrghasemi@eng.usb.ac.ir
2
استاد، دانشکده مهندسی شهید نیکبخت، دانشگاه سیستان و بلوچستان، زاهدان، ایران
LEAD_AUTHOR
سید روح الله
موسوی
s.r.mousavi@eng.usb.ac.ir
3
دانشیار ، دانشکده مهندسی شهید نیکبخت، دانشگاه سیستان و بلوچستان، زاهدان
AUTHOR
[1] Nehme S.G., Lászl R., Mir A.E., Mechanical performance of steel fiber reinforced self-compacting concrete in plane, Procedia Engineering, 2017; 196:90 – 96
1
[2] Fuente A, Pujadas P, Blanco A, Aguado A, Experiences in Barcelona with the use of fibres in segmental linings. Tunneling and Underground Space Technology 2012;27:60–71
2
[3] Iqbal sh, Ali A, Holschemacher A, Bier TH. Mechanical properties of steel fiber reinforced high strength lightweight self-compacting concrete (SHLSCC). Constr. Build. Mater 2015;98:325–333
3
[4] Azhdary MoghaddaM M., Miri M., Rigi M., The effect of rebar coating types on bars corrosion of self-compacting concrete, JSCE, 2017: 172-185
4
[5] Sanginabadi K., Rostami R., Habibi N., Mostofinejad D., Zarrebini M., Fracture mechanics of fiber reinforced concrete: Experimental study of composition, geometry and hybridization of fibers, JSCE, 2018: 83-94
5
[6] Madandoust R, Ranjbar M.M, Ghavidel R, Shahabi F. Assessment of factors influencing mechanical properties of steel fiber reinforced self-compacting concrete. Mat. Des. 2015;83:284–294
6
[7] Hillerborg A. Results of three comparative test series for determining the fracture energy GF of concrete. Mater Struct 1985;18:407–413
7
[8] Bazant Z, Pfeiffer P, Determination of fracture energy from size effect and brittleness number, ACI Mater. J 1987;84:463–480.
8
[9] Alberti MG, Enfedaque A, Galvez JC. Comparison between polyolefin fibre reinforced vibrated conventional concrete and self-compacting concrete. Constr . Build. Mater 2015;85: 182–194
9
[10]-Kazemi M.T., Golsorkhtabar H., Beygi M.H.A, Gholamitabar M., Fracture properties of steel fiber reinforced high strength concrete using work of fracture and size effect methods, Constr. Build. Mater. 2017;142: 482–489
10
[11] Ghasemi M., Ghasemi M.R., Mousavi S.R., Investigating the effects of maximum aggregate size on self-compacting steel fiber reinforced concrete fracture parameters, Constr. Build. Mater. 2018;162: 674–682.
11
[12] ] Karamloo M., Mazloom M., Payganeh G.,Influences of water to cement ratio on brittleness and fracture parameters of self-compacting lightweight concrete, Engineering Fracture Mechanics, 2016; 168: 227-241
12
[13] Sahin Y, Koksal F. The influences of matrix and steel fibre tensile strengths on the fracture energy of high-strength concrete. Const. Build. Mater, 2011;25:1801–1806
13
[14] RILEM FMC-50. Determination of the fracture energy of mortar and concrete by means of three-point bend tests on notched beams. Mater Struct 1985;18(4):287–290.
14
[15] ASTM C 1609/C 1690M-07. Standard test method for flexural performance of fiber reinforced concrete (using beam with third-point loading) 2007: 1–8
15
[16] RILEM TC-169-SOC. Indirect test for stress-crack opening curve 2007
16
[17] RILEM TC-89. Size-effect method for determining fracture energy and process zone size of concrete. Mater Struct 1990;23(6):461–465.
17
[18] Bazant ZP , Kazemi MT, Determination of fracture energy, process zone length and brittleness number from size effect, with application to rock and concrete, IJFr 1990;44:111–131
18
[19] EFNARC, The European Guidelines for Self-Compacting Concrete, Specification, Production and Use 2005
19
[20] Bazant ZP, Becq-Giraudon E, Statistical prediction of fracture parameters of concrete and implications for choice of testing standard, Cem. Concr. Res, 2002;32:529–556.
20
[21] Dupont L., Vandewalle L., Distribution of steel fibres in rectangular sections, Cem. Concr. Compos. 2005;27:391–398.
21
ORIGINAL_ARTICLE
ارزیابی اثر میراگرهای مایع تنظیم شده(TLD) و تنظیم شده ی اصلاحی(MTLD) بر رفتار لرزه ای قابهای خمشی فولادی
آسیب دیدن سازهها در مقابل زلزلههای بزرگ و از دست رفتن ثروتهای ملی موجب گردیده است که کاهش ارتعاشات سازهها در مقابل باد و زلزله از اهمیت ویژهای برخوردار باشد. یکی از روشهای موثر برای کاهش این ارتعاشات استفاده از سیستم میراگر مایع تنظیم شده میباشد. میراگر مایع تنظیم شده سیستم کنترل غیر فعال سازه میباشد که از تعدادی مخازن حاوی سیال تشکیل شده و در بالاترین نقطه ساختمان قرار داده میشود. انرژی ارتعاشی وارده به سازه از طریق تلاطم مایع درون مخازن مستهلک میگردد. این سیستم برای کنترل ارتعاشات سازههایی که به صورت سیستم یک یا چند درجه آزادی هستند به کار گرفته شده است. در پژوهش حاضر از نوع اصلاح شدهی سیستم کنترل غیر فعال سازهای برای بررثرات میراگر مایع حجمی تنظیم شونده استفاده شده و نتایج آن با دادههای موجود برای نوع سنتی مقایسه گردیده است. در این راستا سه ساختمان ۴، ۸ و ۲۰ طبقه با سه نسبت جرمی میراگر ۱، ۲ و ۳ درصد در نرم افزار ETABS طراحی شدند. در نهایت تحلیلهای استاتیکی بار افزون (Pushover) و تاریخچه زمانی بر روی آنها در نرم افزار OPENSEES انجام شده است. نتایج تحلیلها نشان میدهد که استفاده از این میراگرها جابهجایی پسماند سازههای با سیستم قاب خمشی را تا حد زیادی کاهش می دهد. همچنین عملکرد میراگر مایع تنظیم شدهی اصلاحی در مقایسه با نوع سنتی خود به لحاظ کاهش پاسخ سازه مطلوبتر میباشد.
https://www.jsce.ir/article_86854_5661d0e55f54e8107d6b72fe830e5fbd.pdf
2021-04-21
87
105
10.22065/jsce.2019.165876.1756
میراگر مایع تنظیم شده
میراگر مایع تنظیم شوندهی اصلاحی
کاهش ارتعاشات
تحلیل پوش آور
تحلیل تاریخچه زمانی
نادر
هویدایی
hoveidaei@azaruniv.ac.ir
1
استادیار، دانشکده فنی و مهندسی، دانشگاه شهیدمدنی آذربایجان، تبریز، ایران
LEAD_AUTHOR
میثم
میرزاپور
meysammirzapour4592@gmail.com
2
دانشگاه شهید مدنی آذربایجان
AUTHOR
نازیلا
کاردان
n.kardan@azaruniv.ac.ir
3
دانشکده عمران دانشگاه شهید مدنی آذربایجان، تبریز، ایران
AUTHOR
[1] Kaneko, S. and Ishikawa, M. 1999, “Modeling of Tuned Liquid Damper with Submerged Nets,” Journal of Pressure Vessel Technology, ASME, 121: 334-343.
1
[2] Jin, k, Toshihiro, w, 1999, " A Non-Linearing Numerical Model of the Tuned Liquid Damper" Journal of Eaerthquake Engineering and Stractural Dynamics, Vol. 28, pp. 671-686.
2
]3[. برزگری، ب. صباغ یزدی، س.ر. (1393)، بررسی عددی تاثیر شکل مخازن میراگرهای TLD بر عملکرد آنها، نهمین سمپوزیوم پیشرفتهای علوم و تکنولوژی، مشهد.
3
]4[. رضایی، س. علمی، م. منتظری نمین، م. زهرایی، م. (1393)، طراحی میراگر TLD برای کاهش ارتعاشات سازههای نیمه مرتفع عمرانی، هشتمین کنگره ملی مهندسی عمران، بابل.
4
[5] Li, H.N. Jia,Y. and Wang, S.Y. 2004, “Theoretical and Experimental Studies on Reduction of Multi-Modal Seismic Response of High-Rise Structures by Tuned Liquid Dampers,” Journal of Vibration and Control, (10): 1041-1056.
5
[6] Conner, J. J, 2003, "Introduction to Structural Motion Control", Journal of Prentice Hall Pearson Education. Pp 528-541.
6
[7] Tait, M, El Damatty, A, Isyumov, 2004, "Testing of Tuned Liquid Damper with Screens and Development of Equivalent TMD Model" , Wind and Structures, Vol. 7, No. 4, pp. 215-234.
7
[8] Nanda, B. 2010, "Application of Tuned Liquid Damper for Controlling Structural Vibration" PhD diss.
8
[9] Banerji, P. and Samanta, A. 2011, “Earthquake Vibration Control of Structure Using Hybrid Mass Liquid Damper”, Engineering Structure, 33(4): 1291-1301.
9
[10] Mondal, J. H. Nimmala, Sh. Abdulla, R.T. 2014, Tuned Liquid Damper, International Conference on Mechanical Engineering and Mechatronics, 14-15.
10
[11] Veļičko, J. Gaile, L. 2015, "Overview of Tuned Liquid Dampers and Possible Ways of Oscillation Damping" International Scientific and Practical Conference, 233-238.
11
[12] Ashasi, A. Malekghasemi, H. Ghaemmaghami, A. Mercan, O. 2016, ''Experimental Investigations of Tuned Liquid Damper-Structure Interactions in Resonance Considering Multiple Parameters'' Journal of Sound and Vibration, 136.1 (1990): 1-15.
12
[13] Saha, S. Debbarma, R. 2017, ''An Experimental study on Response Control of Structures Using Multiple Tuned Liquid Dampers Under Dynamic Loading'' International Journal of Advanced Structural Engineering, 9(1), 27-35.
13
[14] Chang, Y. Noormohamed, A. Mercan, O. 2018, '' Analytical and Experimental Investigations of Modified Tuned Liquid Dampers (MTLD)'' Journal of Sound and Vibration, 428, 179-194.
14
]15[. نشریه شماره 360، 1392، دستورالعمل بهسازی لرزهای ساختمانهای موجود، سازمان مدیریت و برنامه ریزی کشور، تهران، جمهوری اسلامی ایران.
15
[16] Seismosoft, 2013, Seismomatch v2. 1—A computer program for spectrum matching of earthquake records.
16
]17[. حسینی بای، س.م. غلامزاده، م. دو خطی کردن منحنی پوش آور و تعیین ضریب رفتار به روش چوپرا، سومین کنفرانس سالانه پژوهشهای معماری، شهرسازی و مدیریت شهری، شیراز، 1396.
17
ORIGINAL_ARTICLE
بررسی آزمایشگاهی تاثیر استفاده از ریزدانه و پودر دولومیت به صورت مجزا بر خواص فیزیکی بتن متخلخل
استفاده از سیستم بتن متخلخل در مناطق شهری به عنوان یک رویکرد مدیریتی نوین و کاربردی در هنگام بارندگی میتواند با خروج و انتقال سریع رواناب سطحی، از مشکلاتی که در پی خواهد داشت جلوگیری نماید. در این تحقیق تاثیر جایگزین کردن کانی معدنی دولومیت در دو حالت ریزدانه و پودر، به ترتیب به عنوان بخشی از سنگدانه مصرفی و در تیمارهای دیگر به عنوان بخشی از سیمان مصرفی، بر روی خواص سازه ای بتن متخلخل بررسی شده است.به منظور استفاده از بتن متخلخل در سیستم مدیریت رواناب شهری، باید مقاومت فشاری و تخلخل مناسب مد نظر قرارگیرد. جهت انجام آزمایشهای سازه ای دو سری نمونه ساخته شده است. نمونههای 15×15×15 سانتیمتر برای آزمایش مقاومت فشاری و نمونههایی با ابعاد 10×10×10 سانتیمتر جهت مشخص شدن درصد تخلخل ساخته شد. تحلیل های آماری نتایج آزمایشگاهی با استفاده از نرم افزار SPSS انجام گرفت. برطبق نتایج بدست آمده جایگزین کردن پودر دولومیت به جای سیمان تاثیر قابل ملاحظه ای روی مقاومت فشاری و تخلخل نداشته است. از طرف دیگر استفاده از ریزدانه دولومیت تاحد بسیار خوبی مقاومت فشاری را بهبود داده است. در نمونه هایی که 10٪ ریزدانه جایگزین شده است علاوه بر افزایش مقاومت فشاری، افزایش تخلخل به دلیل ماکانیزم قرار گیری ذرات حاصل شد. همچنین افزودن 30٪ ریزدانه، مقاومت فشاری را 162٪ افزایش داده است. این درحالی است که درصد تخلخل با کاهش شدید مواجه شد.
https://www.jsce.ir/article_86856_e00b3edae518d19b7228cef1e2df8312.pdf
2021-04-21
106
118
10.22065/jsce.2019.169233.1770
"رواناب شهری"
"بتن متخلخل"
"دولومیت"
"مقاومت فشاری"
"ریزدانه"
سعید
فرزین
saeed.farzin@semnan.ac.ir
1
استادیار گروه مهندسی آب و سازه های هیدرولیکی، دانشکده مهندسی عمران، دانشگاه سمنان
LEAD_AUTHOR
مهران
منوچهری نیا
mehran3560@gmail.com
2
دانشجوی کارشناسی ارشد مهندسی عمران مدیریت منابع آب /دانشکده مهندسی عمران/دانشگاه سمنان/سمنان/ایران
AUTHOR
حجت
کرمی
hkarami@semnan.ac.ir
3
استادیار گروه مهندسی آب و سازه های هیدرولیکی، دانشکده مهندسی عمران، دانشگاه سمنان
AUTHOR
فرهاد
موسوی
smousavi@semnan.ac.ir
4
استاد گروه مهندسی آب و سازه های هیدرولیکی، دانشکده مهندسی عمران، دانشگاه سمنان
AUTHOR
[1] Henderson, V. and Tighe, S. (2012). “Evaluation of pervious concrete pavement performance in cold weather climates.” International Journal of Pavement Engineering, Vol. 13, 3. pp 197-208.
1
[2] Kim, H. H., Kim, C. S., Jeon, J. H. and Park, C. G. (2016). “Effects on the Physical and Mechanical Properties of Porous Concrete for Plant Growth of Blast Furnace Slag, Natural Jute Fiber, and Styrene Butadiene Latex Using a Dry Mixing Manufacturing Process. Materials, 9(2), 84.
2
[3] Guruji, A. L. and Rana, A. V. (2015). “Ground Water Recharging Throgh Pervious Concrete Pavement.” Patel Institute of Technology and Research Centre, pp 132-139.
3
[4] Ghasemi, M. A., Mokhtarani, N. and Kavusi, A. (2016). “Removal of Heavy Metals from Surface Runoff Using Permeable Pavement Aggregate Layers.” Journal of Transportation Engineering. Vol. 7(3), pp 629-640.
4
[5] Moghaddam, A. R., Ghallehban Tekmedash, M. and Esmaili, M. (2013). “Investigation of temporal and spatial trend of water quality parameters in view of weather fluctuations using GIS; Mashhad Plain.” Water and Soil Conservation. Vol. 20(3). pp 211-244.
5
[6] Azad, A. (2017). “Application of porous concrete containing adsorbent as a new approach in improving the quality of urban runoff.” Master of Science Thesis. Semnan University.
6
[7] Mahalingam, R. and Vaithiyalingam Mahalingam, Sh. (2016). “Analysis of Pervious Concrete Properties.” Gradevinar. Vol (6). pp 493-501.
7
[8] Bentz, D. P. (2008). “Virtual Pervious Concrete: Microstructure, Percolation, and Permeability.” ACI Materials Journal. Vol. 105(3), 297.
8
[9] Lim, E., Fwa, T. F. and Tan, K. H. (2015). “Laboratory evaluation of clogging behavior of pervious concrete pavements.” Journal of the Eastern Asia Society for Transportation Studies, 11, 1603-1612.
9
[10] Hidayah, N. and Putra Jaya, R. (2014). “Effect of Coarse Aggregate Sizes on Properties of Porous Concrete Paving Blocks.” Advanced Materials Research. Vol. 911. pp 433-437.
10
[11] Kovac, M. and Sicakova, A. (2017). “Changes of Strength Characteristics of Pervious Concrete Due to Variations in Water to Cement Ratio.” In IOP Conference Series: Earth and Environmental Science. Vol. 92, No. 1.
11
[12] Teymouri, E., Mousavi, S. F., Karami, H. and Farzin, S. (2016). “Performance of Porous Concrete Containing Additive in Reduction of Urban Runoff.” Journal of Structural Engineering. Vol. 13(1). pp 33-44.
12
[13] Tennis, P. (2004). “Pervious Concrete Pavement.” Portland Cement Assoc.
13
[14] Doostmoammadi, M., Karami, H., Farzin, S. and Mousavi, S. F. (2018). “Experimental Study of the Influence of Natural Lightweight Aggregates on Some Physical Properties of Porous Concrete Pavement and Providing the Relationship between Compressive Strength and Porosity”. Journal of Transportation Infrastructure Engineering. Vol. 4(1), pp 87-99.
14
[15] Lian, C. and Zhuge, Y. (2010). "Optimum mix design of enhanced permeable concrete–an experimental investigation". Construction and Building Materials. Vol 24(12), pp 2664-2671.
15
[16] Yang, Z., Ma, W., Shen, W. and Zhou, M. (2008), “The Aggregate Gradation for the Porous Concrete Pervious Road Base Material.” Journal of Wuhan University of Technology-Materials Science Edition, Vol. 23(3), pp 391-394.
16
[17] Ćosić, K., Korat, L., Ducman, V and Netinger, I. (2015), “Influence of Aggregate Type and Size on Properties of Pervious Concrete.” Construction and Building Materials, Vol. 78, pp 69-76.
17
[18] Lian, C. and Zhuge, Y. 2010. “Optimum Mix Design of Enhanced Permeable Concrete – An Experimental Investigation.” Construction and Building Materials, Vol. 24, pp 2664-2671.
18
[19] Yang, Z., Ma, W., Shen, W and Zhou, M. (2008), “The Aggregate Gradation for the Porous Concrete Pervious Road Base Material.” Journal of Wuhan University of Technology-Materials Science Edition, Vol. 23(3). pp 391-394.
19
[20] Mikhailova, M., Yakovlev, G. Maeva and I. Senkov, S. (2013). “Effect of Dolomite Limestone Powder on the Compressive Strength of Concrete.” Procedia Engineering. Vol. 57. pp 775-780.
20
[21] ACI Committee 211. 2006. “Guide for Selecting Proportions for No-slump Concrete.” ACI 211.3R Report.
21
[22] ASTM C127. 2001. “Density, Relative Density (Specific Gravity) and Absorption of Coarse Aggregate.” American Society for Testing and Materials.
22
[23] Rahmani, K. Shamsai, A. Saghafian, B. and Peroti, S. 2012. “Effect of Water and Cement Ratio on Compressive Strength and Abrasion of Microsilica Concrete.” Journal of Scientific Research.Vol. 12(8). pp 1056-1061.
23
[24] Haselbach, M., Valavala, S. and Montes, F. (2015).” Permeability Predictions for Sand-Clogged Portland Cement Pervious Concrete Pavement Systems.” Journal of Environmental Management. Vol. 81. pp 42-49.
24
[25] ASTM C1754/C1754M-12. 2012. Standard Test Method for Density and Void Content of Hardened Pervious Concrete. ASTM International, USA.
25
[26] Shirgir, B. Hassani, A. and Alizadeh Goodarzi, H. 2010. “The Influence of Aggregate Gradation on the Permeabilitys and Mechanical Propertie of Porous Concrete”. Modares Civil Engineering Journal. Vol. 11(1). pp 49-60.
26
ORIGINAL_ARTICLE
بررسی پاسخ ساختمانهای فولادی مجهز به مهاربندهای کمانش ناپذیر در برابر خرابی پیشرونده
در مطالعه حاضر استفاده از مهاربندهای کمانش ناپذیر که به دلیل جلوگیری از کمانش مهاربند، قابلیت جذب انرژی بسیار بیشتری را نسبت به سیستم های رایج مهاربندی همگرا فراهم می آورند، به عنوان نوآوری تحقیق با هدفِ کاهش پتانسیل خرابی پیشرونده در قابهای فولادی مهاربندی شده مورد ارزیابی قرار گرفته است. برای این منظور مدل اجزاء محدود سه بعدی ساختمانهای 4، 8 و 12 طبقه در دو حالت استفاده از مهاربندهای معمولی و کمانش ناپذیر شبیه سازی شدند و پاسخ آنها در برابر خرابی پیشرونده مورد ارزیابی قرار گرفته است. بررسی خرابی پیشرونده با استفاده از روش مسیر بار جایگزین صورت پذیرفت و پاسخ سازه ها در برابر حذف ستون مورد بررسی قرار گرفت. شبیهسازی مدلها با استفاده از نرم افزار ABAQUS انجام شد. همچنین صحت روش اجزاء محدود مورد استفاده در شبیه سازی مدلهای مورد بررسی ارزیابی شد و تطابق مناسبی بین نتایج حاصل مشاهده گردید. مهم ترین نتایج حاصل نشان می دهد که قاب های فولادی که دارای مهاربندهای کمانش ناپذیر می باشند، در مقایسه با قاب های فولادی دارای مهاربندهای معمولی متحمل تنش های کمتری شده اند؛ بطوریکه در تمامی حالت ها، مهاربندهای کمانش ناپذیر با جذب انرژی ورودی سازه، سبب شده اند که تنش های کمتری به سایر اعضای سازه وارد شود و بدین ترتیب پتانسیل وقوع خرابی پیشرونده کاهش یابد. همچنین استفاده از مهاربند کمانش ناپذیر سبب شده است که دوران محل اتصال تیر به ستون در مقایسه با ساختمانهای با مهاربند معمولی کاهش یابد. این اثرگذاری بویژه در ساختمانهای با ارتفاع بیشتر مشهودتر میباشد؛ بطوریکه مقدار بیشینه چرخش مفصل متناظر با ساختمان 12 طبقه دارای مهاربند کمانش ناپذیر در مقایسه با مهاربند معمولی به میزان 21 درصد کاهش یافته است.
https://www.jsce.ir/article_86778_fc85cefa0ee136c9832c3e1283b9df1e.pdf
2021-04-21
119
140
10.22065/jsce.2019.153064.1688
خرابی پیشرونده
مهاربند کمانش ناپذیر
روش اجزای محدود
روش مسیر بار جایگزین
BRB
یعقوب
محمدی
yaghoubm@uma.ac.ir
1
دانشیار گروه مهندسی عمران، دانشگاه محقق اردبیلی، اردبیل، ایران
LEAD_AUTHOR
میثم
باقری پوراصیل
meysam_bagheri_p@yahoo.com
2
کارشناس ارشد مهندسی سازه، دانشگاه محقق اردبیلی، اردبیل، ایران
AUTHOR
[1] Burkholder, M. C. (2012). Performance Based Analysis of a Steel Braced Frame Building With Buckling Restrained Braces. A Thesis presented to the Faculty of California Polytechnic State University, San Luis Obispo.
1
[2] Stephen, D., Lam, D., Forth, J., Ye, J., & Tsavdaridis, K. D. (2019). An evaluation of modelling approaches and column removal time on progressive collapse of building. Journal of Constructional Steel Research, 153, 243-253. DOI org/10.1016/j.jcsr.2018.07.019
2
[3] Suwondo, R., Cunningham, L., Gillie, M., & Bailey, C. (2019). Progressive collapse analysis of composite steel frames subject to fire following earthquake. Fire Safety Journal, 103, 49-58. DOI org/10.1016/j.firesaf.2018.12.007.
3
[4] Meng, B., Zhong, W., Hao, J., Song, X., & Tan, Z. (2019). Calculation of the resistance of an unequal span steel substructure against progressive collapse based on the component method. Engineering Structures, 182, 13-28. DOI org/10.1016/j.engstruct.2018.12.053.
4
[5] Hoveidae, N. (2019). Comparison of Progressive Collapse Capacity of Steel Moment Resisting Frames and Dual Systems with Buckling Retrained Braces. Journal of Rehabilitation in Civil Engineering, 7(3), 61-70.
5
[6] Karimian, A., Armaghani, A., & Behravesh, A. (2019). Performance of Low-yield Strength Plates in Beam-column Connections against Progressive Collapse. KSCE Journal of Civil Engineering, 23(1), 335-345. DOI //doi.org/10.1007/s12205-018-0653-y.
6
[7] Shirinzadeh, M., & Haghollahi, A. (2019). Rehabilitation in Simple Steel Connections against Progressive Collapse due to Column Removal. KSCE Journal of Civil Engineering, 1-7. DOI org/10.1007/s12205-018-0935-4.
7
[8] Naghavi, M., Rahnavard, R., Thomas, R. J., & Malekinejad, M. (2019). Numerical evaluation of the hysteretic behavior of concentrically braced frames and buckling restrained brace frame systems. Journal of Building Engineering, 22, 415-428. doi.org/10.1016/j.jobe.2018.12.023.
8
[9] Xie, L., Wu, J., Huang, Q., & Tong, C. (2019). Analysis of the Seismic Demand of High-Performance Buckling-Restrained Braces under a Strong Earthquake and Its Aftershocks. Advances in Civil Engineering. DOI org/10.1155/2019/1482736
9
[10] Zaruma, S., & Fahnestock, L. A. (2018). Assessment of design parameters influencing seismic collapse performance of buckling-restrained braced frames. Soil Dynamics and Earthquake Engineering, 113, 35-46. DOI org/10.1016/j.soildyn.2018.05.021
10
[11] Esfandiari, J., & Soleimani, E. (2018). Laboratory investigation on the buckling restrained braces with an optimal percentage of microstructure, polypropylene and hybrid fibers under cyclic loads. Composite Structures, 203, 585-598. DOI org/10.1016/j.compstruct.2018.07.035
11
[12] Palmer, K. D., Roeder, C. W., Lehman, D. E., Okazaki, T., & Shield, C. (2012). Experimental performance of steel braced frames subjected to bidirectional loading. Journal of Structural Engineering, 139(8), 1274-1284. DOI org/10.1061/(ASCE)ST.1943-541X.0000624.
12
[13] Hosseini, S. M., & Amiri, G. G. (2017). Successive collapse potential of eccentric braced frames in comparison with buckling-restrained braces in eccentric configurations. International Journal of Steel Structures, 17(2), 481-489. DOI org/10.1007/s13296-017-6008-6.
13
[14] Faghihmaleki, H., Nejati, F., Zarkandy, S., & Masoumi, H. (2017). Evaluation of Progressive Collapse in Steel Moment Frame with Different Braces. Jordan Journal of Civil Engineering, 11(2).
14
[15] Bagheripourasil, M., Mohammadi, Y., & Gholizad, A. (2017). A proposed procedure for progressive collapse analysis of common steel building structures to blast loading. KSCE Journal of Civil Engineering, 1-9. DOI org/10.1007/s12205-017-0559-0.
15
[16] Akbarinia, F., Adinehfar, Y., Davashi, H., Jalili, D., Beiranvand, P., & Hosseini, M. (2018). Investigating the effect of column removal on progressive collapse of buildings designed by buckling restrained braced and bending frames. Engineering Solid Mechanics, 6(1), 83-88. DOI 10.5267/j.esm.2017.10.001.
16
[17] Abaqus theory manual.Version,Hibbitt. 2016. Pawtucket (RI): Karlsson and Sorensen, Inc.
17
[18] Feng Fu. (2012) Response of a multi-storey steel composite building with concentric bracing under consecutive column removal scenarios. Journal of Constructional Steel Research, 70 115–126. DOI org/10.1016/j.jcsr.2011.10.012.
18
[19] ETABS, C. (2015). 15.0. Berkeley. CA: Computers and Structures inc.
19
[20] DOD, (2013), Design of Buildings to Resist Progressive Collapse, Unified Facilities Criteria (UFC) 4-023-03, Department of Defence, Washington, DC, 2013.
20
[21] Tsai, K. C. (2013). Buckling restrained braces: Resear chand implementation in Taiwan. In Steel Innovations Conference. Steel Innovations Conference, Christchurch, New Zealand.
21
[22] AISC, (2010). Seismic provisions for structural steel buildings, American Institute of Steel Construction, Inc., Chicago, Illinois.
22
[23] Song BI. (2010). Experimental and analytical assessment on the progressive potential of existing buildings. Master’s thesis. The Ohio State University; 2010. p. 125.
23
[24] Kaafi, Pouya Ghodrati Amiri, Gholamreza, (2014), Investigation of the Progressive Collapse Potential in Steel Buildings with Composite Floor System, World Academy of Science, Engineering and Technology, International Journal of Civil and Environmental Engineering Vol:1, No:8.
24
[25] GSA. (2003), Progressive collapse analysis and design guidelines for federal office buildings and major modernization projects.The U.S.General Services Administration.
25
ORIGINAL_ARTICLE
بررسی بارکمانش ارتجاعی ستون های یکنواخت و غیریکنواخت تحت بار محوری غیریکنواخت با استفاده از روش اجزای محدود
نیاز به استفاده از اعضای غیریکنواخت در سازه از گذشته تا به حال مطرح بوده است در عین حال موضوعات و مراجع تحقیقی در این مورد زیاد نمیباشند. در مورد این اعضا یکی از مهمترین مسائلی که باید مورد بررسی قرار گیرد کمانش ستونها است که در صورت رخ دادن، باعث از دست رفتن عضو میگردد که ممکن است منجر به فروپاشی موضعی یا کل ستون و یا سازه شود. در این مقاله روشی دقیق بر اساس اجزای محدود برای بررسی مسئله کمانش ارتجاعی ستونهای یکنواخت و غیر یکنواخت با هر سطح مقطع و هر حالت بارگذاری ارائه شده است. این روش برای تمام شرایط مرزی تکیهگاهی قابل کاربرد است. در ابتدا ستون را به تعداد جزء دلخواه تقسیم-بندی کرده و سپس ماتریس سختی و ماتریس سختی هندسی را بر اساس روابط موجود برای هر جزء و سپس برای کل ستون تشکیل شده است و پس از اعمال شرایط تکیهگاهی با استفاده از رابطهی مقدار مشخصه بار بحرانی کمانش بدست آمده است. نتایج این روش با روش سایر محققین که به صورت تقریبی محاسبه شدهاند مقایسه شده است. روش ارائه شده علاوه بر دقت بالا دارای جامعیت نیز می-باشد و با کمک برنامه کدنویسی شده Matlab میتوان از آن بهره گرفت.
https://www.jsce.ir/article_86848_d20f789483c8603581abb2b6df269147.pdf
2021-04-21
141
158
10.22065/jsce.2019.153522.1689
کمانش ارتجاعی
ستون های یکنواخت و غیریکنواخت
بار محوری
مقدار مشخصه
روش اجزای محدود
مسعود
محمودآبادی
m.mahmoudabadi@qom.ac.ir
1
استادیار، دانشکده فنی و مهندسی، دانشگاه قم، قم، ایران
LEAD_AUTHOR
سیدمحمدرضا
حسنی
smr.hasani@yahoo.com
2
دانشجوی دکتری عمران- سازه، دانشگاه صنعتی نوشیروانی، بابل، ایران.
AUTHOR
رضا
اکبری
smr.civil@yahoo.com
3
گروه مهندسی عمران، دانشکده عمران، قم، ایران
AUTHOR
[1] Ziemian, R. D. (2010). Guide to stability design criteria for metal structures, 6th Edition, John Wiley & Sons, Inc, pp. 12-114
1
[2] Elishakoff,I. (2004). Eigenvalues of Inhomogenous Structures: Unusual Closed-form Solutions, CRC Press.
2
[3] Riahi, H. T., Shojaei Barjoui , A., Bazazzadeh, S., and Etezady, S.M.A. (2012). Buckling Analysis of Non-Prismatic Columns Using Slope-Deflection Method. 15th World Conference on Earthquake Engineering. Lisbon, Portugal, September 28700-28710.
3
[4] Serna , M .A. , Ibanez, J .R. , Lopez, A.(2011). Elastic flexural buckling of non-uniform members: Closed-form expression and equivalent load approach. Journal of Constructional Steel Research, Vol. 67, pp. 1078-1085.
4
[5] Hadianfard, M .A., Sharbati. R. (1392). Numerical simulation of retracted steel bonding connections and investigation of the role of connecting components in its behavior. Journal of Modeling in Engineering, Vol. 34, pp. 11-24.
5
[6] Fafhi, M .A., Hasani. R. (1396). Finite element modeling A proposed rigid connection for prefabricated concrete buildings using a steel interface element. Journal of Modeling in Engineering, Vol. 49, pp. 189-200.
6
[7] Hasani, S.M.R., Mahmoudabadi. M., Danaei, R,. (1397). Investigating effect of boundary conditions on columns’ buckling. Journal of Structural and Construction Engineering(JSCE), Vol. 5, pp. 143-156.
7
[8] Aristizabal-Ochoa,J. D. (2013). Stability of slender columns on an elastic foundation with generalised end conditions. Ingeniera e Investigacion, Vol. 33, No. 3, pp. 34 - 40.
8
[9] Arboleda-Monsalve, L. G., Zapata-Medina, D. G. and AristizabalOchoa,J. D.,Timoshenko. (2008). beam-column with
9
generalized end conditions on elastic foundation: Dynamic-stiffness matrix and load vector., Journal of Sound and Vibration,
10
Vol. 310, pp.1057-1079.
11
[10] Zapata-Medina, D. G. Arboleda-Monsalve, L. G. AristizabalOchoa, J. D. (2010). Static Stability Formulas of a Weakened
12
Timoshenko Column: Effects of Shear Deformations. J. of Engineering Mechanics-ASCE, Vol. 126, No. 12,pp.1-9.
13
[11] Eisenberger, M. (1991), Buckling Loads For Variable Cross-Section Members With Variable Axial Forces, Int.J.Solids Structures, Vol. 27, pp. 135-143.
14
[12] Yoo, C. H., Lee, L. (2011). Stability of structures principles and applications, Elsevier, pp. 133.
15
[13] MATLAB, "The Language of Technical Computing", (2008), Version 7.6.0. The Math-works Inc.: Natick, MA
16
ORIGINAL_ARTICLE
بررسی درصدهای مختلف الیاف فلزی جهت بهبود مشخصات مکانیکی و دوام بتن در دماهای بالا
یکی از عوامل آسیب و تخریب سازههای بتنی آتش سوزی میباشد. سازههای بتنی علاوه بر داشتن مشخصات مکانیکی مناسب، میبایست خواص دوام قابل قبولی نیز داشته باشند تا در طول عمر مفید سازه از ظرفیت خود استفاده نمایند. در این مطالعه تاثیردرصدهای حجمی مختلفی از الیاف فلزی در بهبود مشخصات مکانیکی و دوام بتن در دماهای مختلف بررسی شده است. مشخصات مکانیکی شامل مقاومت فشاری و مقاومت کششی بتن در حالت داغ و مشخصات دوام بتن حرارت دیده شامل جذب آب سطحی، عمق نفوذ آب، مقاومت الکتریکی و افت وزنی در آزمایشگاه بررسی شده اند. این مطالعه مقادیر 0.25 و 0.50 درصد حجمی الیاف فلزی و دماهای 28 تا 800 درجه سانتیگراد را پوشش میدهد. نتایج نشان داده است که افزایش مقاومت فشاری و کششی ناشی از افزایش سن نمونه ها، در بتن الیافی بیش از بتن بدون الیاف بوده است. همچنین ملاحظه گردید که افزودن الیاف فلزی به میزان 0.25 و 0.5 درصد حجمی مقاومت فشاری را به در محدوده 10 تا 27 درصد و مقاومت کششی را در محدوده 8 تا 200 درصد در دماهای بررسی شده بهبود داده است. از طرف دیگر کاربرد الیاف فلزی در بتن توانسته است موجب کاهش جذب آب سطحی، عمق نفوذ آب و مقاومت الکتریکی بتن شده و از افت وزنی بتن ناشی از حرارت بکاهد. جمع بندی نتایج این مطالعه نشان داده است که در دماهای کمتر و بیشتر از 500 درجه سانتیگراد، به ترتیب افزودن 0.25 و0.5 درصد حجمی الیاف بهترین عملکرد را در بهبود مشخصات مکانیکی و دوام بتن معمولی داشتهاست.
https://www.jsce.ir/article_86855_7668d771a0de3e8999388aebca1296c2.pdf
2021-04-21
159
176
10.22065/jsce.2019.166490.1757
"مشخصات مکانیکی"
"مشخصات دوام"
"الیاف فلزی"
" بتن"
"حرارت بالا"
رمضانعلی
ایزدی فرد
izadifard@eng.ikiu.ac.ir
1
گروه مهندسی عمران- دانشکده فنی مهندسی- دانشگاه بین المللی امام خمینی (ره)- قزوین- ایران
LEAD_AUTHOR
مهرداد
عبدی مقدم
2
دانشجوی دکتری سازه، دانشگاه بین المللی امام خمینی (ره)، قزوین، ایران
AUTHOR
[1] Xing, Z. Beaucour, A.-L. Noumowe, A. and Ledesert, B. (2015). Aggregate’s influence on thermophysical concrete properties at elevated temperature. Constr. Build. Mater., vol. 95, pp. 18–28.
1
[2] Fletcher, I. A. Borg, A. Hitchen, N, and Welch, S. (2006). Performance of concrete in fire: a review of the state of the art, with a case study of the Windsor tower fire.
2
[3] Meacham, B. Engelhardt, M. and Kodur, V. (2009). Collection of data on fire and collapse, faculty of architecture building, delft university of technology. in Proc. of NSF Engineering Research and Innovation Conference, Honolulu, Hawaii.
3
[4] Ewen, S. “Grenfell Lessons,” Firefighter, pp. 14–15, 2017.
4
[5] Wikipedia, (2018). Available at: https://en.wikipedia.org/wiki/2018_California_wildfires.
5
[6] Novák, J. and Kohoutková, A. (2017). Fibre reinforced concrete exposed to elevated temperature. in IOP Conference Series: Materials Science and Engineering, vol. 246, no. 1, p. 12-45.
6
[7] Masoud, M. A. (2015). Compresive Strengths And Modulus Of Elasticity Of Steel Fiber Reinforced Concrete Under Different Temperature Conditions. Master of Engineering. Universitas Muhammadiyah Surakarta.
7
[8] Khalil, L. W. I. (2018). Influence of high temperature on steel fiber reinforced concrete. J. Eng. Sustain. Dev., vol. 10, no. 2, pp. 139–150.
8
[9] Kim, J. and Lee, G.-P. (2015). Evaluation of mechanical properties of steel-fibre-reinforced concrete exposed to high temperatures by double-punch test. Constr. Build. Mater., vol. 79, pp. 182–191.
9
[10] Gholhaki, M. Pachideh, Gh. and Rezayfar, O. (2017). An experimental study on mechanical properties of concrete containing steel and polypropylene fibers at high temperatures. Journal of structutal and construction engineering. vol. 4, no. 3, pp. 167–179.
10
[11] Rao, K. S. and Narayana , S. R. K. A. L. (2013). Comparison of performance of standard concrete and fibre reinforced standard concrete exposed to elevated temperatures. Am. J. Eng. Res., vol. 3, pp. 20–26.
11
[12] Faiyadh, F. I. and Al-Ausi, M. A. (1989). Effect of elevated temperature on splitting tensile strength of fibre concrete. Int. J. Cem. Compos. Light. Concr., vol. 11, no. 3, pp. 175–178.
12
[13] Yermak, N. Pliya, P. Beaucour, A.-L. Simon, A. and Noumowé, A. (2017). Influence of steel and/or polypropylene fibres on the behaviour of concrete at high temperature: Spalling, transfer and mechanical properties. Constr. Build. Mater., vol. 132, pp. 240–250.
13
[14] Aslani, F. and Samali, B. (2014). Constitutive relationships for steel fibre reinforced concrete at elevated temperatures. Fire Technol., vol. 50, no. 5, pp. 1249–1268.
14
[15] Uysal, M. and Akyuncu, V. ( 2012 ). Durability performance of concrete incorporating Class F and Class C fly ashes. Constr. Build. Mater., vol. 34, pp. 170–178.
15
[16] Tasdemir, C. (2003). Combined effects of mineral admixtures and curing conditions on the sorptivity coefficient of concrete. Cem. Concr. Res., vol. 33, no. 10, pp. 1637–1642.
16
[17] Leung, H. Y. Kim, J. Nadeem, A. Jaganathan, J. and Anwar, M. P. (2016). Sorptivity of self-compacting concrete containing fly ash and silica fume. Constr. Build. Mater., vol. 113, pp. 369–375.
17
[18] Mendes, A. Sanjayan, J. G. Gates, W. P. and Collins, F. (2012). The influence of water absorption and porosity on the deterioration of cement paste and concrete exposed to elevated temperatures, as in a fire event. Cem. Concr. Compos., vol. 34, no. 9, pp. 1067–1074.
18
[19] Chen, J. J. Kwan, A. K. H. and Jiang, Y. (2014). Adding limestone fines as cement paste replacement to reduce water permeability and sorptivity of concrete. Constr. Build. Mater., vol. 56, pp. 87–93.
19
[20] Beglarigale, A. Ghajeri, F. Yiğiter, H. and Yazıcı, H. (2014). Permeability Characterization of Concrete Incorporating Fly Ash. 11th International congress on advances in civil engineering. İstanbul.
20
[21] Kubissa, W .and Jaskulski, R. (2013). Measuring and time variability of the sorptivity of concrete. Procedia Eng., vol. 57, pp. 634–641.
21
[22] Dabbagh, H. and Mohammaddoost, H. (2017). Influence of fiber geometry on the mechanical properties of structural steel fiber lightweight concrete made with Scoria aggregate. Journal of structutal and construction engineering. vol. 4, no 1. pp. 17–25.
22
[23] Afroughsabet, V. and Ozbakkaloglu, T. (2015). Mechanical and durability properties of high-strength concrete containing steel and polypropylene fibers. Constr. Build. Mater., vol. 94, pp. 73–82.
23
[24] Kakooei, S. H. Akil, M. Jamshidi, M. and Rouhi, J. (2012). The effects of polypropylene fibers on the properties of reinforced concrete structures. Constr. Build. Mater., vol. 27, no. 1, pp. 73–77.
24
[25] B. S. EN, 1-2: 2004 Eurocode 2: Design of concrete structures-Part 1-2: General rules-Structural fire design. (2004). Eur. Stand. London.
25
[26] AISC 360-10. (2010). Chicago, IL.
26
[27] B. Standard, Testing hardened concrete, Compressive Strength Test Specimens. (2009) BS EN, pp. 12390–12393.
27
[28] Xiao, J. Xie, Q. and Xie, W. (2018). Study on high-performance concrete at high temperatures in China (2004–2016)-An updated overview. Fire Saf. J., vol. 95, pp. 11–24.
28
[29] Castillo, C. (1987). Effect of transient high temperature on high-strength concrete. Rice University, Houston, Texas.
29
[30] Naus, D. J. The effect of elevated temperature on concrete materials and structures-a literature review. ( 2006). Oak Ridge National Laboratory (United States). Funding organisation: .
30
[31] Morsy, M. S. Rashad,A. M. and Shebl, S. S. Effect of elevated temperature on compressive strength of blended cement mortar. (2008). Build Res J, vol. 56, no. 2–3, pp. 173–185.
31
[32] Peng, G.-F. and Huang, Z.-S. (2008). Change in microstructure of hardened cement paste subjected to elevated temperatures,” Constr. Build. Mater., vol. 22, no. 4, pp. 593–599.
32
[33] Khoury, G. A. Anderberg, Y. Both, K. Fellinger, J. Høj, N. P. and Majorana, C. (2007). Fib bulletin 38: fire design of concrete structures—materials, structures and modelling, state-of-the art report. Fed. Int. du beton, Lausanne, Switz.
33
[34] Rashad, A. M. Bai, Y. Basheer, P. A. M. Collier, N. C. and Milestone, N. B. (2012). Chemical and mechanical stability of sodium sulfate activated slag after exposure to elevated temperature. Cem. Concr. Res., vol. 42, no. 2, pp. 333–343.
34
[35] C. ASTM, 496/C 496M-04. (2004). Stand. Test Method Split. Tensile Strength Cylind. Concr. Specimens.C. ASTM, “496/C 496M-04,” Stand. Test Method Split. Tensile Strength Cylind. Concr. Specimens, 2004.
35
[36] Novak, J. and Kohoutkova, A. ( 2018). Mechanical properties of concrete composites subject to elevated temperature,” Fire Saf. J., vol. 95, pp. 66–76.
36
[37] Silva, P. C. Ferreira, R. M. and Figueiras, H. (2011). Electrical resistivity as a means of quality control of concrete–influence of test procedure,” in International Conference on Durability of Building Materials and Components. Porto. Portugal. vol. 12.
37
[38] Zheng, W. Li, H. and Wang, Y. (2012). Compressive behaviour of hybrid fiber-reinforced reactive powder concrete after high temperature,” Mater. Des., vol. 41, pp. 403–409.
38
ORIGINAL_ARTICLE
ارزیابی زمان گیرش و مقاومت فشاری خمیر ژئوپلیمر حاوی سرباره کوره آهنگدازی و زئولیت
از آنجا که تولید سیمان پرتلند فرآیند بسیار انرژی بری است و آثار مخرب زیست محیطی به همراه دارد، محققین همواره در صدد یافتن راهکاری برای کاهش مضرات و بهینه سازی این فرآیند می باشند. ژئوپلیمرها از جمله موادی هستند که جهت جایگزینی سیمان در بتن مورد استفاده قرار می گیرند. ژئوپلیمر از ترکیب یک یا چند ماده پایه که حاوی آلومینوسیلیکات است با فعال ساز قلیایی حاصل می شود.این بررسی به منظور ارزیابی زمان گیرش و مقاومت فشاری خمیر ژئوپلیمری بر پایه سرباره کوره آهنگدازی و زئولیت انجام گرفته است. بدین منظور اندازه گیری زمان گیرش خمیر ژئوپلیمر بر پایه سرباره کوره آهنگدازی و زئولیت فعال سازی شده با هیدروکسید سدیم 6، 8، 10 و 12 مولار و سیلیکات سدیم با مدول سیلیکاتی 2 انجام شد. در مرحله بعد مقاومت فشاری نمونه های خمیر ژئوپلیمری عمل آوری شده در دمای محیط آزمایشگاه و نیز دمای 60 درجه سانتی گراد اندازه گیری شد.نتایج نشان داد که افزایش غلظت هیدروکسید سدیم زمان گیرش را افزایش می دهد، همچنین مقاومت فشاری نمونه خمیر ژئوپلیمر حاوی سرباره و زئولیت با بالارفتن غلظت هیدروکسید سدیم افزایش یافته است. نمونه های خمیر بر پایه سرباره با بالا رفتن غلظت هیدروکسید سدیم در غلظت های 6، 8 و 10 مولار با افزایش مقاومت فشاری مواجه شدند اما با افزایش غلظت هیدروکسید سدیم به 12 مولار مقاومت فشاری کاهش یافته است. همچنین با بالارفتن درصد جایگزینی زئولیت در ماده پایه زمان گیرش افزایش و مقاومت فشاری کاهش یافت. نمونه های عمل آوری شده در دمای 60 درجه سانتی گراد نیز مقاومت بهتری از خود نشان دادند.
https://www.jsce.ir/article_87089_2d66a07db45dec8d129569cbf89ab014.pdf
2021-04-21
177
187
10.22065/jsce.2019.161256.1740
آلومینوسیلیکات
ژئوپلیمر
سیلیکات سدیم
هیدروکسید سدیم
عمل آوری
مریم
محمدی فتیده
mohammadi.ft9@gmail.com
1
دانشجوی کارشناسی ارشد عمران سازه، دانشکده فنی دانشگاه گیلان، رشت، ایران
AUTHOR
ملک محمد
رنجبر
ranjbar@guilan.ac.ir
2
دانشیار گروه عمران، دانشکده فنی دانشگاه گیلان، رشت، ایران
LEAD_AUTHOR
[1] Prasanna Venkatesan, R. and Pazhani, K.C. (2015). Strength and durability properties of geopolymer concrete made with ground granulated blast furnace slag and black rice husk ash. KSCE Journal of Civil Engineering, 20(6), 2384-2391.
1
[2] Li, Zh. and Li, Sh. (2018). Carbonation resistance of fly ash and blast furnace slag based geopolymer concrete. Construction and Building Materials, 163, 668-680.
2
[3] Gunasekara, C., Law, D.W., Setunge, S. and Sanjayan, J.G. (2015). Gel formation and compressive strength of low calcium fly ash geopolymers. Construction and Building Materials, 95, 592-599.
3
[4] Revathi, T., Jeyalakshmi, R. and Rajamane, N.P. (2018). Geopolymeric binder: The effect of silica fume addition on fly ash activation by using response surface methodology. Materials Today: Proceedings, 5(2), 8727-8734.
4
[5] Davidovits, J. (2009). Geopolymer chemistry and applications book. Geopolymer Institute, St Quentin, France.
5
[6] Jafari Nadoushan, M. and Ramzanianpour, A.A. (2016). The effect of type and concentration of activators on flowability and compressive strength of natural pozzolan and slag-based geopolymers. Construction and Building Materials, 111, 337-347.
6
[7] Deb, P.S., Nath, P. and Sarker, P.K. (2015). Drying shrinkage of slag blended fly ash geopolymer concrete cured at room temperature. Procedia Engineering, 125, 594-600.
7
[8] Chen, L., Wang, Z., Wang, Y. and Feng, J. (2016). Preparation and properties of alkali activated metakaolin based geopolymer. Materials, 9(9), 767.
8
[9] Duan, P., Yan, Ch. And Zhou,W. (2017). Compressive strength and microstructure of fly ash based geopolymer blended with silica fume under thermal cycle. Cement and composites, 78, 108-119.
9
[10] Rattanasak,U. and Chindaprasirt, P. (2009). Influence of NaOH solution on the synthesis of fly ash geopolymer. Minerals Engineering, 22(12), 1073-1078.
10
[11] Hanjitsuwan, S., Hunpratub, S., Thongbai, P., Maensiri, S., Sata, V. and Chindaprasirt, P. (2014). Effects of NaOH concentrations on physical and electrical properties of high calcium fly ash geopolymer paste. Cement and Concrete Composites, 45, 9-14.
11
[12] Gorhan, G., Aslaner, R. and Sinik,O. (2016). The effect of curing on the properties of metakaolin and fly ash based geopolymer paste. Composites Part B: Engineering, 97, 329-335.
12
[13] Saha, S. and Rajasekaran, C. (2017). Enhancement of the properties of fly ash based geopolymer paste by incorporating ground granulated blast furnace slag. Construction and Building Materials, 146, 615-620.
13
[14] American Society for Testing and Materials (ASTM) C191-08. Standard test method for time of setting of hydraulic cement by vicat needle.
14
[15] Chindaprasirt, P., De Silva, P., Sagoe-Crentsil, K. and Hanjitsuwan, S. (2012). Effect of SiO2 and Al2O3 on the setting and hardening of high calcium fly ash-based geopolymer system. Materials Science, 47(12), 4876-4883.
15
[16] Mo, B.H., He, Zh., Cui, X.M., He, Y. and Gong, S.Y. (2014). Effect of curing temperature on geopolymerization of metakaolin based geopolymers. Applied Clay Science, 99: 144-148.
16
[17] Heah, C.Y., Kamarudin, H., Mustafa Al Bakri, A.M., Bnhussain, M., Luqman, M., Khairul Nizar, I., Ruzaidi, C.M. and Liew, Y.M. (2012). Study on solids-to-liquid and alkaline activater ratios on kaolin-based geopolymers. Construction and Building Materials, 35: 912-922.
17
[18] Papa, E., Medri, V., Amari, S., Manaud, J., Benito, P., Vaccari, A. and Landi, E. (2018). Zeolite geopolymer composite materials production and characterization. Cleaner Production.
18
ORIGINAL_ARTICLE
بررسی آزمایشگاهی مقاومت فشاری و کششی بتن پودری (RPC) دارای الیاف فولادی
بتن پودری (RPC) از جمله بتن های فوق توانمند (UHPC) با ویژگی های فیزیکی و مکانیکی برتر است.RPC با بهره گیری از سیمان و مصالح پودری بسیار ریز دانه شامل ماسه کوارتزی، میکروسیلیس، مقادیر کم نسبت آب به سیمان و استفاده از فوق روان کننده تولید می-شود. نتایج آزمایش های انجام شده به منظور استخراج طرح اختلاط بهینه برای بتن پودری نشان می دهد که نسبت آب به مصالح پودری (W/B) که متناظر با حداکثر مقاومت فشاری است برابر با 15/0 بوده که مربوط به طرح اختلاط با نسبت فوق روان کننده به سیمان (SP/C) برابر با 3 درصد است. دیر زمانی است که ایده اضافه کردن الیاف به انواع مختلف بتن به منظور بهبود ویژگی های فیزیکی و مکانیکی آن مورد توجه قرار گرفته است. در این پژوهش تاثیر افزودن الیاف فولادی بر مقاومت فشاری و کششی RPC با انجام آزمایش هایی مورد بررسی قرار گرفته است. نتایج حاصل از آزمایش بیانگر آن است که میانگین مقاومت فشاری نمونه های با 1، 2 و 3 درصد حجمی از الیاف، به ترتیب افزایشی در حدود 6، 20 و 5 درصد نسبت به نمونه های بدون الیاف را نشان می دهد. این افزایش در مقاومت کششی به ترتیب مشابه برابر 46، 73 و 66 درصد می باشد.
https://www.jsce.ir/article_87090_7ab653d19d364f4df7911730f1a222f4.pdf
2021-04-21
188
200
10.22065/jsce.2019.167555.1762
بتن پودری
بتن فوق توانمند
مقاومت فشاری
مقاومت کششی
الیاف فولادی
محمد علی
دشتی رحمت آبادی
dashti@iauyazd.ac.ir
1
استادیار گروه عمران، واحد یزد، دانشگاه آزاد اسلامی، یزد، ایران
AUTHOR
فرزاد
شهابیان مقدم
shahabf@um.ac.ir
2
استاد گروه عمران، گرایش سازه، دانشکده مهندسی، دانشگاه فردوسی مشهد، مشهد، ایران
LEAD_AUTHOR
حسن
حاجی کاظمی
hkazemi@um.ac.ir
3
استاد گروه عمران، گرایش سازه، دانشکده مهندسی، دانشگاه فردوسی مشهد، مشهد، ایران
AUTHOR
[1] Richard, P., Cheyrezy, M. (1995), Composition of Reactive Powder Concretes. Cement and Concrete Research, Vol. 25, No. 7, pp. 1501-1511.
1
[2] Long, G., Wang, X. and Xie, Y. (2002). Very-High-Performance Concrete with Ultrafine Powders. Cement and Concrete Research, Vol. 32, No. 4, pp. 601-605.
2
[3] Wong, A.C.L., Childs, P.A., Berndt, R., Macken, T., Peng, G.D. and Gowripalan, N. (2007). Simultaneous Measurement of Shrinkage and Temperature of Reactive Powder Concrete at Early-Age Using Fibre Bragg Grating Sensors. Cement and Concrete Composites, Vol. 29, No. 6, pp. 490-497.
3
[4] Zhang, M.H., Tam, C.T. and Leow, M.P. (2003). Effect of Water-to-Cementitious Materials Ratio and Silica Fume on the Autogenous Shrinkage of Concrete. Cement and Concrete Research, Vol. 33, No. 10, pp. 1687-1694.
4
[5] Habel, K., Denarie, E. and Bruhwiler, E. (2006). Structural Response of Elements Combining Ultrahigh-Performance Fibre–Reinforced Concretes. Journal of Structural Engineering, ASCE, Vol. 132, No. 11, pp. 1793 – 1799.
5
[6] Hoang, K.H., Phat, B. and Van Chanh, N. (2008). Influence of Types of Steel Fibre on Properties of Ultra High Performance Concrete. The 3rd ACF International Conference-ACF/VCA, pp.347-355.
6
[7] Mindess, S., Young, J.F. and Darwin, D. (2003). Concrete. 2nd Edition, Prentice Hall, New Jersey.
7
[8] Neville, A.M. (1995). Properties of Concrete. 4th Edition, Addison Wesley Longman Ltd., London.
8
[9] Reschke, T. (2000). Influence of Granulometry of Fines on the Microstructure Development and the Strength of Concrete. Series of the Cement Industry, Issue 62. (In Germany)
9
[10] Wild, S., Sabir, B.B. and Khatib, J.M. (1995). Factors Influencing Strength Development of Concrete Containing Silica Fume. Cement and Concrete Research, Vol. 25, No. 7, pp. 1567-1580.
10
[11] Rhaei, A. and Zomorrodian, A. (2005). Restoration and reinforcement of composite polymer fiber reinforced concrete structures (FRP). Tafresh University Press. (In Persian)
11
[12] Beddar, M. (2008). Development of steel fiber reinforced concrete from antiquity until the present day. Proceedings of International Conference on Concrete: Constructions sustainable option, Dundee, U.K., pp. 35-44.
12
[13] Bonneau, O., Lachemi, M., Dallaire, E., Dugat, J., and Aitcin, P.C. (1997). Mechanical Properties and Durability of Two Industrial Reactive Powder Concretes. ACI Materials Journal, Vol. 94, No. 4, pp. 286-290.
13
ORIGINAL_ARTICLE
تحلیل دینامیکی دودکش های فولادی با احتساب مولفه های دورانی زمین لرزه
در این تحقیق اثر مولفههای دورانی ناشی از زمینلرزه بر رفتار دینامیکی خطی دودکشهای فولادی مورد تحلیل و بررسی قرار گرفته است. بدین منظور در این مطالعه ابتدا مولفههای دورانی ناشی از چهار زمینلرزه با استفاده از مولفههای انتقالی و در نظر گرفتن سرعت امواج وابسته به فرکانس به دست آمده است. در ادامه برای بررسی اثرات این مولفهها بر پاسخ دینامیکی دودکشهای فولادی، شش مدل دودکش فولادی با ارتفاعهای مختلف تحت بارگذاری مولفههای چهار زلزله متفاوت در حالات اعمال مولفههای دورانی و انتقالی بصورت همزمان و اثر تنها مولفه های انتقالی تحت تحلیل و بررسی قرار گرفته است. نتایج عددی تحلیلهای لرزهای حاکی از آن است که مقادیر بیشینه تغییرمکانها، تنشها و برش پایه دچار تغییرات بسزایی شده و محل رخداد ماکزیمم پاسخ ها دچار تغییر شده است. همچنین نتایج نشان از تاثیر مولفه های دورانی بر پاسخ سازهها با افزایش ارتفاع، و نزدیکی فرکانس غالب مولفه دورانی و فرکانس غالب سازه دارد به طوریکه در برخی موارد اعمال مولفه های دورانی باعث کاهش میزان پاسخ ها شده و در مواردی با نزدیک تر شدن فرکانس این مولفه ها و فرکانس غالب سازه و نیز افزایش ارتفاع سازه مقدار پاسخ ها بصورت قابل توجهی افزایش مییابد. این نتایج نشانگر اهمیت احتساب مولفه های دورانی زمینلرزه در آنالیز و طراحی این نوع از سازه ها می باشند.
https://www.jsce.ir/article_87091_fe067a6e95e1e3354ab85cccf07776a5.pdf
2021-04-21
201
223
10.22065/jsce.2019.170911.1776
تحلیل لرزه ای
دودکش فولادی
مولفه های دورانی
زمین لرزه
روش اجزا محدود
امیرجواد
مرادلو
ajmoradloo@znu.ac.ir
1
استادیار بخش مهندسی عمران، دانشکده فنی و مهندسی، دانشگاه زنجان
LEAD_AUTHOR
حسین
بیات
hbayat47@znu.ac.ir
2
استادیار بخش مهندسی عمران، دانشکده فنی و مهندسی، دانشگاه زنجان
AUTHOR
احسان
تیموری
eteymouri@znu.ac.ir
3
دانشجوی دکتری مهندسی عمران، دانشکده فنی و مهندسی، دانشگاه زنجان
AUTHOR
[1] Rajkumar, V. and Vishwanath, B.Patil. (2013). “Analysis of Self-Supporting Chimney”. International Journal of Innovative Technology and Exploring Engineering (IJITEE), 3(5), Page (85-91).
1
[2] Rohini Padmavathi, V. and Siva Konda Reddy, B. and Srikanth. (2012). “Study of wind load effects on tall RC chimneys”. Int. J. of Advanced Engineering Technology, 3(2), Page (92-97).
2
[3] Reddy, K. R. C. and Jaiswal, O. R. and Godbole, P. N. (2011). “Wind and Earthquake Analysis of Tall RC Chimneys”. Int. J. of ISSN 0974-5904, 4(6), Page (508-511).
3
[4] Kirtikanta S, Pradip S, Robin D. (2013). ”Analysis of self-supported steel chimney with the effects of manhole and geometrical Properties”. Int. J. of Scientific and Engineering Research, 4(5), Page (250-253).
4
[5] Reddy, B T K. S M. Hussain, S M A M. (2014). ” Analysis of Self Supported Steel Chimney with Effect of Manhole”. Int. J. of Scientific and Engineering, 4(5).
5
[6] Sagar S, Basvaraj G. (2015). ”Performance based seismic evaluation of industrial chimney by static and dynamic analysis “. Int. R. J. of Engineering and Technology, 2(4), Page (1670-1674).
6
[7] Rakshit B D, Ranjit A, Sanjith J, Chetan G. (2015). ”Analysis of Contilever Steel Chimney as per Indian Satandard”. J. of Engineering Search and Applications”, 5(5), Page (151-162).
7
[8] Rekadi Rama, S V. Reddy, V P. (2016). “Computerized Virtual Study on Self-Supporting and Guyed Steel Chimney”. Int. J. of Engineering and Technology, 3(5), Page(778-791).
8
[9] Deshpande, H. John, R. (2015). “Correlation of Geometry and Dynamic Response of Self Supported Short Circular Steel Stacks”. Int. J. of Engineering Technology Science and Research IJETS R, 2(Special Issue), Page (133-144).
9
[10] Devil, B. Singh, S, S. (2016). ”Analysis of self supporting Steel Stacks with Variable Geometrical Configuration under the seismic loading for different shapes”. Int. J. of Engineering Research and General Science, 4(4), Page (229-233).
10
[11] Santhi, K. Sridhar, P. (2017). “Analysis of Self Supported Steel Chimney”. Int. J. for Research in Applied Science & Engineering Technology (IJRASET), 5(3), Page (651-656).
11
[12] Kumar, M, A. Raju, P, M. Babu, N, V. Roopesh, K. (2017). ”A parametric study on lateral load resistance of steel chimneys”. Int. J. of Civil Engineering and Technology, 8(7), Page (858-875).
12
[13] Kalpesh, D. Shrirang, T. Abhijeet, O. (2018). ” analysis of self support steel chimney with the effects of geometrical Parameters”. Int. J. of Engineering Research and Application, 8(5), Page (4-9).
13
[14] Newmark, N M. (1969). ”Torsion in symmetrical buildings”. In: 4th World Conf. on Earthquake Engineering, 2. Santiago, Chile, Page (19- 32).
14
[15] Ghafory-Ashtiany, M. Singh, M P. (1986). “Structural response for six correlated earthquake components”. Int. J. of Earthquake Engineering and Structural Dynamic, 14(1), Page (103-119).
15
[16] Trifunac, M D. (1982). “A note on rotational components of earthquake motions on ground surface for incident body waves”. Int. J. of Soil Dynamics and Earthquake Engineering, 1(1), Page (11-19).
16
[17] Lee, V W. Trifunac, M D. (1985). “Torsional accelerograms”. Int. J. of Soil Dynamics and Earthquake Engineering, 4(3), Page (132-139).
17
[18] Lee, V W. Trifunac, M D. (1987). “Rocking strong earthquake accelerations”. Int. J. of Soil Dynamic and Earthquake Engineering, 6(2), Page (75-89).
18
[19] Castellani, A. Boffi, G. (1986). “Rotational components of the surface ground motion during an earthquake”. Int. J. of Earthquake Engineering and Structural Dynamic, 14(5), Page (751-767).
19
[20] Castellani, A. Boffi, G. (1989). “On the rotational components of seismic motion”. Int. J. of Earthquake Engineering and Structural Dynamic, 18(6), Page (785-797).
20
[21] Nouri, GR. Ghayamghamian, MR. Hashemifard, M. (2010). “A comparison among different methods in the evaluation of torsional ground motion”. Int, J. of Iran Geophysics, 4(2), Page (32-44).
21
[22] Hong-Nan, L. Sun, L. Wang, SY. (2004). ” Improved approach for obtaining rotational components of seismic motion”. Int. J. of Nuclear Engineering and Design, 232(2), Page (131-137).
22
[23] Lee, V W. Liang, L. (2008) “Rotational components of strong motion earthquakes”. In: 14th World Conf. on Earthquake Engineering, Beijing, China.
23
[24] Kalani Sarokolayi, L. Navayi Neya, B. Tavakoli, H R. (2012). “Rotational Components Generation of Earthquake Ground Motion Using Translational Components”. In: 15th World Conference on Earthquake Engineering, Lisbon.
24
[25] Kalani Sarakolayi, L. Navayi Neya, B. Vaseghi Amiri, J. Tavakoli, H R. (2013). “Seismic Analysis of Evaluated water Storage Tanks Subjected to Six Correlated Ground Motion Component”. Int. J. of Iranica Journal of Energy & Environment, 4(3), Page (199-207).
25
[26] Ghazvini, T. Tavakoli, H. Navayineya, B. Kalani Sarakolayi, L. (2013). “Seismic analysis of above ground storage steel tanks subjected to six correlated earthquake components”. Int. J. of Latin American Journal of Solids and Structures, 10(6), Page (1155-1176).
26
[27] Sandeep, C. Desai, Raviji, S. Gupta, D. (2010) '' Practical Engineering Approach For Generating The torsional Earthquake Excitation From Translational component”. Int. J. of Advanced Structural Engineering, 4(1), Page (1-10).
27
[28] ANSYS Inc.: ANSYS Documentation Version 12.1
28
[29] Bathe, K. J. (1996). “Finite element procedures”, In Engineering Analysis”. 2th Edn. Prentice Hall: University of Michigan, Page (768-769).
29
[30] Devi, B. Singh, S, S. (2016).” Analysis of Self supporting Steel Stacks with Variable Geometrical Configuration under the seismic loading for different shapes”. Int. J. of Engineering Research and General Science, 4(4), Page (229-233(.
30
ORIGINAL_ARTICLE
رفتارسازه ای پانهای ساندویچی بتنی پیش ساخته یک طرفه و دوطرفه با لایه تحتانی متفاوت و هسته بتن سبک تحت بارخمشی
در این مقاله رفتار سازه ای پانلهای ساندویچی پیش ساخته تحت خمش بررسی شده است. تحلیل اجزاء محدود پانلهای ساندویچی بتنی پیشساخته کامپوزیت جهت امکان استفاده آنها در ساخت و سازهای صنعتی مطالعه شده است. این پانلها متشکل ازسه لایه میباشند,لایهها عبارتند از: یک لایه بتن مسلح پرمقاومت به عنوان لایه فوقانی، یک لایه ضخیم از بتن سبک به عنوان لایه میانی یا هسته و یک صفحه فلزی نازک مسطح یا کنگرهای و یا یک لایه بتن مسلح مقاوم در مقابل کشش به عنوان لایه تحتانی. در این پژوهش ابتدا 8 مدل پانلهای یکطرفه و دو طرفه ساندویچی پیشساخته بتنی با هسته بتن سبک در نرم افزار ABAQUS مدل-سازی شده و از لحاظ عملکرد سازهای مورد بررسی قرار گرفتهاند. تاثیرسختی اتصال دهندههای برشی که با توجه به قطر آنها اندازه گیری میشود بر روی مقاومت نهایی و میزان عملکرد مرکب پانل بررسی شده است. همچنین تاثیر جهت گیری اتصالات برشی در یک و دو جهت نیز مورد بررسی قرار گرفته است. نتایج مدل اجزا محدود پانلها در نرم افزار ABAQUS رفتاری منطقی از منحنی بار- تغییر مکان دراتصال دهندههای برشی بدست آمده است. مقاومت نهایی و درجه عملکرد کامپوزیت به میزان بسیار زیادی به سخت کنندههای اتصالات برشی استفاده شده بستگی دارد.
https://www.jsce.ir/article_87595_44935b70eb2ad09a3984308af6300e0d.pdf
2021-04-21
224
243
10.22065/jsce.2019.141493.1614
آنالیز المان محدود
هسته
بتن سبک
پانل ساندویچی
پیش ساخته
اتصالات برشی
کامپوزیت
الله داد
احمدی
arastoo588@gmail.com
1
دانشجوی دکتری سازه، گروه مهندسی عمران، واحد مرودشت، دانشگاه آزاد اسلامی، مرودشت، ایران
AUTHOR
آرش
توتونچی
totonchi@miau.ac.ir
2
استادیار، گروه مهندسی عمران، واحد مرودشت، دانشگاه آزاد اسلامی، مرودشت، ایران
LEAD_AUTHOR
اشکان
ترابی
ashkantorbi@miau.ac.ir
3
استادیار، گروه مهندسی عمران، واحد مرودشت، دانشگاه آزاد اسلامی، مرودشت، ایران
AUTHOR
داود
صفری
4
استادیار، گروه مهندسی عمران، واحد شیراز، دانشگاه آزاد اسلامی، شیراز، ایران
AUTHOR
[1] Paul M, Hopkins. A Chen. Mostafa, Yossef. (2017). Static and dynamic analyses of insulated concrete sandwich panels using a unified non-linear finite element model. Journal of Engineering Structures 132 (2017) 249–259.
1
[2] Thomas, G. Norris, An Chen. (2016). Development of insulated FRP-confined Precast Concrete Sandwichpanel with side and top confining plates and dry bond. Journal of Composite Structures 152 (2016) 444–454.
2
[3] Karthik Ram Ramakrishnan and et al, (2016). Experimental study of the medium velocity impact response of sandwich panels with different cores. Journal of Materials and Design 99 (2016) 68–82.
3
[4] Mugahed, Amran. Y.H. Raizal, S.M. Rashid, Farzad Hejazi, Nor Azizi Safiee, A. A. Abang Ali. (2016). Structural behavior flaterally loaded precast foamed concrete sandwich panels, Int. J. Civ. Environ. Struct. Constr. Arch. Eng. 10(3).
4
[5] Mugahed, Amran, Y. H. Raizal, S.M. Rashid, Farzad Hejazi, Nor Azizi Safiee, A. A. Abang Ali. (2016). Response of precast foamed concrete sandwich panels to flexural loading. Journal of Building Engineering,7 (2016)143–158.
5
[6] J, Daniel Ronald Joseph. J, Prabakar. P, Alagusundaramoorthy. (2016). Flexural behaviour of precast concrete sandwich panels under different loading conditions such as punching and bending. Journal of Alexandria Engineering, xxx, xxx–xxx
6
[7] Hamid, Kazem. William G. Bunn, Hatem M. Seliem, Sami H. Rizkalla, Harry Gleich. (2015). Durability and long-term behavior of FRP/foam shear transfer mechanism for concrete sandwich panels. Journal of Construction and Building Materials 98 (2015) 722–734.
7
[8] Noridah, Mohammad. A. I. Khalil, A. A. Abdul Samad, and W.I. Goh. (2014). Structural behavior of Precast Light-Weight Foam Concrete Sandwich Panel with Double Shear Truss Connectors under Flexural Load. Hindawi Publishing corporation ISRN Civil Engineering Volume 2014,7 Pages.
8
[9] Mohammed Hussin, A. D. (2013). Structural Behavior of Composite Sandwich Slab Panels. Journal of Engineering and Development, Vol. 17, No.4, October 2013, ISSN 1833-7822.
9
[10] Ahmad, I. Mohamad, N. (2011). Structural behavior of precast lightweight concrete sandwich panel under Eccentric Load: An over view. University Tun Hussein Onn Malaysia.
10
[11] Schumann, E. Vallee, T. and Keller, T. (2008). Direct load transmission in sandwich slabs with lightweight concrete core. Tailor Made Concrete Structures-Walraven & Stoelhorst (eds) 2008 Taylor & Francis Group, London, lSBN 978-0-415-47535-8.
11
[12] Schumann, E. vallee, T. and Keller, T. (2008). Direct load transfer of hybrid FRP-concrete sandwich structure for bridge decks. Fourth International Composites in Civil Engineering. CICE2008. 22-24 July, Zurich, Switzerland.
12
[13] Schumann, E. (2008). Hybrid FRP-lightweight concrete sandwich system for Engineering structures. Thesis, Dipl. Lag. Vniversitat Karlsruhe Allemagne et De Nationalite Allemande.
13
[14] Benayoune, A. Abang Ali, A. Abdul samad, A. And trikha, D. (2007). Flexural analysis of composite one-and two-way sandwich slabs with truss-shaped connectors. Journal, The Institution of Engineers, Malaysia vol. 68, No.1March 2007.
14
[15] Benayoune, A. samad, A. A. A. Abang Ali, A. A. and trikha, D. N. (2007). Response of pre-cast reinforced composite sandwich panels to axial loading. Journal of Construction and building materials, page 677-685.
15
[16] Benayoune, A. Abdul samad, A. A. Trikha, D. N. Abang Ali, A.A., and Elianna, s. H. M. (2008). Flexural behavior of pre- cast concrete sandwich composite Panel-Experimental and theoretical investigations. science direct. Journal of Construction and Building Materials, page 580-592
16
[17] Einea, A. Salmon, D. Tadros, M. and Culp, T. (1994). A new structurally and thermally efficient precast sandwich panel system. PCI, Journal, July-August1994,90-101.
17
[18] ABAQUS, Finite Element Program Theory Manual (version 6. 12. 1). Hibbit, Karlssson & Sorenson Inc. USA,1993.
18
[19] Kent D.C. and park R. (1971). Flexural Members with Confined Concrete, Journal of Structural Division, Proceedings of the American Society of Civil Engineers, Vo l.97, No. ST7,1969-1990
19
[20] Park R. and parlay T. (1975). Reinforced Concrete Structures, Johen Wiley and Sons.
20
ORIGINAL_ARTICLE
بررسی اثرات میراگر جرمی چندگانه در کاهش پارامترهای لرزه ای ساختمانهای بلند قاب خمشی فولادی منظم و دارای نامنظمی در پلان تحت زلزله های حوزه دور و نزدیک
میراگر جرمی تنظیم شده نوع جدیدی از سیستمهای کنترل سازه می باشد که باعث افزایش اتلاف انرژی میرایی تحت نیروهای خارجی در سازه می گردد. تاکنون در بیشتر موارد تنها یک میراگر جرمی تنظیم شده TMD (Tuned Mass Damper) در بام ساختمان و یا چند میراگر محدود در چندین نقطه در ارتفاع ساختمان نصب می شد، که این مستلزم در نظرگرفتن جرم قابل توجه در نقاطی از سازه به عنوان سربار و همچنین درنظر گرفتن فضایی قابل توجه برای نصب این جرم و از آن مهمتر پیش بینی جسمی که جرم مورد نیاز را تامین کند می باشد. لذا در این تحقیق کارایی میراگر جرمی تنظیم شده توزیعی در طبقات(MTMD) در ساختمان بلند مورد بررسی قرار گرفته و به اثرات میراگر جرمی چندگانه بر روی ساختمان های بلند قاب خمشی فولادی منظم و دارای نامنظمی در پلان پرداخته شده است. مدلهای 10،15،20 طبقه با پلان های منظم و دارای نامنظمی به شکل L,U در نرم افزار SAP2000 مورد تحلیل و طراحی قرار گرفته، سپس در نرم افزار OPENSEES مجهز به میراگر جرمی چندگانه شده و تحت رکوردهای دور و نزدیک از گسل تحلیل دینامیکی غیرخطی شده و مورد بررسی و مقایسه قرار گرفته اند. نتایج نشان می دهد که میراگر جرمی که در طبقات بام قرار گرفته اند از نظر برش حدود 40 درصد کاهش، از نظر جابجایی مطلق طبقات حدود 30 درصد کاهش و از نظر شتاب طبقات حدود 35 درصد کاهش بوده که باعث افزایش کارایی مدل ها شده و وضعیت لرزه ای آنها را بهبود بخشیده اند.
https://www.jsce.ir/article_88288_5f1d7ed19728bfc97e721244d6975b23.pdf
2021-04-21
244
263
10.22065/jsce.2019.176558.1811
میراگر جرمی چندگانه
قاب خمشی فولادی
ساختمان بلند
نامنظمی در پلان
تحلیل دینامیکی غیرخطی
محسن
خزائی
m.khazaei@qiet.ac.ir
1
دانشجوی دکتری، دانشکده مهندسی عمران، دانشگاه سمنان، سمنان، ایران
AUTHOR
رضا
وهدانی
rvahdani@semnan.ac.ir
2
استادیار، دانشکده مهندسی عمران، دانشگاه سمنان، سمنان، ایران
LEAD_AUTHOR
علی
خیرالدین
kheyroddin@semnan.ac.ir
3
استاد، دانشکده مهندسی عمران، دانشگاه سمنان، سمنان، ایران
AUTHOR
[1] Bargi,Kh. (2007). Fundamentals of Earthquake Engineering. First Edittion. University of Tehran.
1
[2] Soto,M. (2012). Investigation of Passive Control of Irregular Building Structures using Bidirectional Tuned Mass Damper . MSC, The Ohio State University.
2
[3] Abbasi,M. (2012). Investigating and evaluating the performance of mass-dampers regulated in reducing the non-elastic seismic requirements of tall buildings. MSC. University of rajaee Tehran.
3
[4] Kareem,A.and Kijewski,T.and Tamura,M. (1999). Mitigation of motions of tall building with specific example of recent application. Journal of Wind and Structure, Vol 2(3), pp 201-251.
4
[5] Carlisle,M. (2013). Experimental Investigation into a Passive Auto-Tuning Mass Damper. MSC, University of the Witwatersrand.
5
[6] Clark,A. (1988). Multiple Passive Tuned Mass Dampers for Reducing Earthquake induced Building Motion. Proceedings of the 9th World Conference on Earthquake Engineering. Tokyo-Kyoto, Japan, Vol 5, pp 779-784.
6
[7] Chen, G. (1996). Multi-stage tuned mass damper. Proceedings of the 11th World Conference on Earthquake Engineering. Acapulco.Mexico, Paper No. 1326.
7
[8] Warburton,G,B. Ayorinde, E, O. (1982). Optimum absorber Parameters for Simple Systems. Journal of Earthquake Engineering and Structural Dynamics, Vol 8(3), pp 197-217.
8
[9] Villaverde, R. and Koyama, L. (1993). Damped Resonant Appendages to Increase Inherent Damping in Buildings. Earthquake Engineering and Structural Dynamics, Vol 22, pp 491–507.
9
[10] Wirsching, P.and Campbell, G.W. (1974). Minimal Structural Response under Random Excitation using the Vibration Absorber. Earthquake Engineering and Structural Dynamics, Vol 2, pp 303–12.
10
[11] Abe,M. and Igusa,T. Tuned Mass Dampers for Structures with Closely Spaced Natural Frequencies. Journal of Earthquake Engineering And Structural Dynamics, Vol 24(2), pp 247-261.
11
[12] Jangid, R.S. (1995). Dynamic Characteristics of Structures with Multiple Tuned Mass Dampers. Structural Engineering and Mechanics. Vol 28, pp 1041-1049.
12
[13] Li, C. (2000). Performance of Multiple Tuned Mass Dampers for Attenuating Undesirable Oscillations of Structures under the Ground Acceleration. Earthquake Engineering and Structural Dynamics, Vol 29, pp 1405-1421.
13
[14] Abdullah,M. and Richardson, Hanif. (2001). Use of a Shared Tuned Mass Damper (STMD)to Reduce Vibration and Pounding in djacent. Structures. Earthquake Engineering and Structural Dynamics, Vol 30, pp 1185-1201.
14
[15] Zahrai,S.M. and Ghannadi,A. (2008). Seismic Performance of TMDs in Improving the Response of MRF Building. Scientia Iranica, Vol 15, No 1, pp 21-33.
15
[16] Tuan,A. and Shang,G.Q. (2014). Vibration Control in a 101-Storey Building using a Tuned Mass Damper. Journal of Applied Science and Engineering, Vol 17, No2, pp 141-156.
16
[17] Hirde,S. and Aher.R. (2016). Seismic Evaluation of Irregular Structures. International Journal of Engineering Research, No 5, pp 750-755.
17
[18] Soto,M.G. and Adeli,H. (2014). Optimum Tuning Parameters of Tuned Mass Damper for Vibration Control of Irregular High Rise Building Structures. Journal of Civil Engineering and Management, Vol 20(5), pp 609-620.
18
[19] Wakchaure,M.R. and Shirish.A, and Nikam,R. (2012). Study of Plan Irregularity on High-Rise Structures. International ournal of Innovative Research&Development, Vol 1(8), PP 269-281.
19
[20] Valmundson,E. and Nau,J.M. (1997). Seismic Response of Building Frames with Vertical Structural Irregularities. Journal of Structure Engineering, ASCE, Vol 123 (1) , pp 30-41.
20
[21] Siva Konda Reddy,B. and Madhavi,L. and Srikanth,CH. (2018). Analysis of Irregular High Raised RCC Buildings by Using Tuned Mass Damping System. International Journal of Advanced Engineering Research and Science(IJAERS), Vol 5(3),
21
[22] Bagheri,S. and Rahmani-Dabbagh,V. (2018). Seismic Response Control with Inelastic Tuned Mass Damper. Journal of Engineering Structures, Vol 172,pp 712-722.
22
[23] Wang, W. and Wang,X. and Hua,X. and Song,G. and Chen, Z. and Chen, Z. (2018). Vibration Bridge Deck by a Single- Side Pounding Tuned Mass Damper. Journal of Engineering Strucures, Vol 173, pp 61-75.
23
[24] Li, Luya. and Peng, Cui. (2017). Novel Approach of a Nonlinear Tuned Mass Damper with Duffing Stiffness. Journal of Engineering Mechanics , Vol 143(4), 04017004.
24
[25] Lu, Zheng, and Kun, Li, and Ying, Zhou. (2018). Comparative Studies on Structures with a Mass Damper and Particle Damper. Journal of Aerospace Engineering. 31(6), 04018090.
25
[26] Lin, Jui-Liang. (2017) Top-Story Mass Dampers for Seismic Control of the First Triplet of Vibration Modes of Two-Way Asymmetric-Plan Buildings. Journal of Vibration and Control. 23(18), pp 2962-2976.
26
[27] Sadek,F. and Mohraz,B. and Taylor,A.W. and Chung, R.M. (1997). A Method of Estimating the Parameters of Tuned Mass Dampers for Seismic Applications. Earthquake Engineering & Structural Dynamic, Vol 26, pp 617-635.
27
ORIGINAL_ARTICLE
تحلیل حساسیت زمان گسیختگی قاب بتنآرمه در شرایط آتشسوزی پس از حذف ستون تحت خرابی پیشرونده
بارهای متوالی میتواند تهدیدی جدی برای ایمنی سازهها باشد. حذف ناگهانی المانهای باربر مانند ستون یکی از عوامل ایجاد خرابی پیشرونده در سازهها میباشد. خرابی موضعی ناشی از حذف ناگهانی ستون میتواند بر رفتار سازه دربارهای متوالی تأثیرگذار باشد.یکی از بارهایی که ایمنی سازه را در طول عمر سازه تهدید میکند بار آتش است. زمانی که یک سازه میتواند در برابر بار آتش مقاومت کند یکی از فاکتورهای اصلی در ایمنی سازهها در برابر بارهای حرارتی است. خرابیهای موضعی موجود در سازه ازجمله حذف ناگهانی المانهای باربر میتواند بر پایداری سازهها در برابر بار آتش بهعنوان دو رویداد متوالی تأثیرگذار باشد. در این تحقیق سعی شده است حساسیت زمان پایداری قاب فولادی در بارگذاری متوالی حذف ناگهانی ستون و آتشسوزی پسازآن نسبت به متغیرهای تصادفی بررسی شود. قاب بتنآرمه 7 طبقه پس از طراحی بهصورت مکانیکی-حرارتی مدلسازی شده و در معرض حذف ناگهانی ستون در موقعیتهای مختلف قرارگرفته است. چندین پارامتر بهعنوان متغیر تصادفی در نظر گرفتهشده است و دو روش مونتکارلو و تحلیل حساسیت مرتبه اول ممان دوم (FOSM) برای انجام تحلیل حساسیت بکار گرفتهشده است. تحلیل حساسیت در قاب بتنآرمه برای تحلیل پوش دان دینامیکی و تحلیل حرارتی پسازآن بهصورت مجزا انجام شده است. نتایج نشان داده است در سناریوی حذف ناگهانی ستون، بار مرده و در سناریوی آتشسوزی پس از آن، بار مرده و پوشش آرماتورها بیشترین حساسیت را نسبت به سایر پارامترها ایجاد کردهاند. همچنین حداکثر خطای تحلیل حساسیت به روش FOSM نسبت به روش مونتکارلو برابر با 11% محاسبه شده است.
https://www.jsce.ir/article_88289_17cc4e28057a947508bfeb239432a9ba.pdf
2021-04-21
264
279
10.22065/jsce.2019.183958.1850
خرابی پیشرونده
آتشسوزی
زمان گسیختگی
تحلیل حساسیت
عدم قطعیت
مجید
مرادی
majid_moradi68@yahoo.com
1
دانشجوی دکتری مهندسی زلزله، دانشگاه صنعتی نوشیروانی بابل
AUTHOR
حمید رضا
توکلی
tavakoli@nit.ac.ir
2
دانشیار، دانشگاه صنعتی نوشیروانی بابل
LEAD_AUTHOR
غلامرضا
عبداله زاده
abdollahzadeh@nit.ac.ir
3
دانشیار، دانشگاه صنعتی نوشیروانی بابل
AUTHOR
[1] Tavakoli, H.R, Moradi Afrapoli, M., (2018), “Robustness Analysis of Steel Structures with Various Lateral Load Resisting Systems under Seismic Progressive Collapse”, Engineering Failure Analysis, 83, 89-101.
1
[2] Tavakoli, H.R, Kiakojouri, F., (2012), “Progressive collapse of frame structures: suggestions for robustness assessment”, Scientia Iranica, 21(2), 329-338.
2
[3] Tavakoli, H.R., Rashidi Alashti, A., (2013), "Evaluation of progressive collapse potential of multi-story moment resisting steel frame buildings under lateral loading" , Scientia Iranica, 20(1), 77-86.
3
[4] Tavakoli, H.R., Naghavi, F. , and Goltabar, R., (2015), “Effect of base isolation systems on increasing the resistance of structures subjected to progressive collapse” Earthquakes and Structures, 9 (3), 639-656.
4
[5]Lew, H., “Best practices Guidelines For Mitigation of Building For progressive collapse”, 2003.
5
[6] Menchel Kfir, Progressive collapse: comparison of main standards, formulation and validation of new computational procedures, PHD thesis, 2009.
6
[7] GSA, "Progressive collapse analysis and design guidelines for new federal office buildings and major modernization projects," General Services Administration Washington (DC, USA), 2003.
7
[8]Unified Facilities Criteria, UFC–DoD, "Design of buildings to resist progressive collapse," 2005.
8
[9] Amiri, S., Saffari, H., Mashhadi, J., (2018), “Assessment of dynamic increase factor for progressive collapse analysis of RC structures”, Engineering Failure Analysis, 84, 300-310.
9
[10] Suwondo, R., Cunningham, L., Gillie, M., Bailey, C., (2019), “Progressive collapse analysis of composite steel frames subject to fire following earthquake”, Fire Safety Journal, 103, 49-58.
10
[11] Qn, C., Mahmoud, H., (2019), “Collapse performance of composite steel frames under fire”, Engineering Structures, 183, 662-676.
11
[12] Jiang, B., Li, G.Q., Li, L., Izzuddin, B.A., (2017), “Simulations on progressive collapse resistance of steel moment frames under localized fire”, Journal of Constructional Steel Research, 138, 380-388.
12
[13] Grabbe, C., (2008), “Progressive Collapse of the World Trade Center: A Simple Analysis”, Journal of Engineering Mechanics, 136, 125-132.
13
[14] Hartanto Wibowo, Modelling Progressive Collapse of RC Bridges during Earthquakes, CSCE Annual General Conference, 2009.
14
[15] Lee, T.H. and Mosalam, K.M., (2005), “Seismic Demand Sensitivity of Reinforced Concrete Shear-Wall Building Using FOSM Method”, Earthquake Engineering and Structural Dynamics, 34:14, 1719-1736.
15
[16] Dwaikat MB, and Kodur VKR, (2010), “Fire induced spalling in high strength concrete beams,” Fire Technology, 46, 1, 251–274.
16
[17] Lie TT, Kodur VKR, (1998), “Thermal and mechanical properties of steel-fibre-reinforced concrete at elevated temperatures,” Canadian Journal of Civil Engineering, vol. 23, no. 2, pp. 511–517.
17
[18] Youssef MA, Moftah M, (2007) ,“General stress–strain relationship for concrete at elevated temperatures”, Engineering Structures, 29(10), 2618–2634.
18
[19] Elhami Khorasani N, Garlock M, Quiel S,(2015), “Modeling steel structures in OpenSees: Enhancements for fire and multi-hazard probabilistic analyses”, Computers and Structures, 157, 218–231.
19
[20] Tian, L.F., Wei, J.P., Hao, J. and Wang, X., (2017), “Dynamic analysis method for the progressive collapse of long-span spatial grid structures”, Steel and Composite Structures, 23 (4), 435-444.
20
[21] Tavakoli, H. And Kiakojouri, F., (2012) "Influence Of Sudden Column Loss On Dynamic Response Of Steel Moment Frames Under Blast Loading," International Journal Of Engineering-Transactions B: Applications, 26, 197-206.
21
[22] Marjanishvili, S. And Agnew, E., (2006) "Comparison Of Various Procedures For Progressive Collapse Analysis," Journal Of Performance Of Constructed Facilities,20, 365- 374.
22
[23] Kim, J. And Kim, T., (2009) "Assessment of Progressive Collapse-Resisting Capacity of Steel Moment Frames," Journal Of Constructional Steel Research, 65, 169-179.
23
[24] Marjanishvili, S. And Agnew, E., (2006) "Comparison Of Various Procedures For Progressive Collapse Analysis," Journal Of Performance Of Constructed Facilities,20, 365- 374.
24
[25] Imani, R., Mosqueda, G., Bruneau, M., (2015), “Experimental Study on Post-Earthquake Fire Resistance of Ductile Concrete-Filled Double-Skin Tube Columns”, Journal of Structural Engineering, Volume 141 Issue 8.
25
ORIGINAL_ARTICLE
ارزیابی تأثیر محتوای فرکانسی بارهای لرزهای بهمنظور شناسایی ناهنجاریهای زیرسطحی با استفاده از امواج رایلی و طولی
آگاهی از خصوصیات زیرسطحی همواره مورد توجه مهندسان بوده است بهخصوص زمانی که احتمال وجود مخاطرات ناشی از ناهنجاریهای زیرسطحی همچون فروچاله یا حفره مدنظر باشد. شناسایی موقعیت این ناهنجاریها در اعماق بیشتر به خاطر کاهش وضوح و دقت دادههای برداشتشده هنوز موضوعی چالشبرانگیز و نیازمند مطالعات بیشتر میباشد. در این مقاله با استفاده از روش اجزا محدود، تأثیر انواع بارهای لرزهای بهمنظور شناسایی حفرات زیرسطحی مورد ارزیابی واقعشده است بارهای لرزهای شامل ضربه چکش، ضربه سینوسی، ضربه کوتاه و بار ریکر با فرکانس های حداکثر 100، 50 و 20 هرتز می باشند. به علاوه اینکه با روشهای فیلتر کردن و جداسازی امواج در فضای میدان موج، توانایی امواج طولی و رایلی جهت شناسایی حفرات در اعماق 2، 6، 10 و 20 مورد مقایسه قرارگرفته است. نتایج حاصله نشان دادند که محتوای فرکانسی و فرکانس غالب بار ارتعاشی، تأثیر قابلتوجهی بر وضوح تصاویر و عمق نفوذ دارند. بهعنوانمثال، بارهای لرزهای ریکر100 هرتز، ضربه چکش و ضربه کوتاه با محتوای فرکانسی بالا برای شناسایی حفرات در عمق 2 متر دارای وضوح خوب، عمق 6 متر دارای وضوح متوسط، عمق 10 متر دارای وضوح ضعیفتر میباشند و برای حفره در عمق 20 متر امواج رایلی برگشتی بهسختی قابلمشاهده بوده ولی در مقابل امواج طولی دارای وضوح و دقت بهتری هستند؛ حالآنکه بار لرزهای با محتوای فرکانسی پایین همچون بار ریکر 20 هرتز نتایج مناسبتری از وضعیت امواج طولی و رایلی بازگشتی از حفره در اعماق بیشتر را فراهم نموده است. بهطورکلی میتوان اینگونه اظهار داشت که استفاده ترکیبی از امواج طولی رایلی و طولی و اعمال بار لرزهای متناسب با عمق شناسایی حفره منجر به نتایج قابل قبولی می گردد.
https://www.jsce.ir/article_88296_c66872e71650fc164736ae19bb129da6.pdf
2021-04-21
280
300
10.22065/jsce.2019.176403.1808
حفره
امواج لرزهای
موج رایلی
موج طولی
بار لرزهای
محتوای فرکانسی
حسین
رهنما
rahnema@sutech.ac.ir
1
استادیار گروه عمران و محیطزیست، دانشگاه صنعتی شیراز، شیراز، ایران
AUTHOR
سهراب
میراثی
s.mirasi@sutech.ac.ir
2
دانشجوی دکتری ژئوتکنیک، گروه عمران و محیط زیست، دانشگاه صنعتی شیراز، شیراز، ایران
LEAD_AUTHOR
[1] Rahnema, H., & Mirasi, S. (2012). Seismic and geotechnical study of land subsidence and vulnerability of rural buildings. International Journal of Geosciences, 3(04), 878.
1
[2] Rahnema, H., & Mirassi, S. (2016). Study of land subsidence around the city of Shiraz. Scientia Iranica. Transaction A, Civil Engineering, 23(3), 882.
2
[3] Park, C. B., Miller, R. D., & Xia, J. (1999). Multichannel analysis of surface waves. Geophysics, 64(3), 800-808. [4] Coduto, D. P. (2015). Foundation design: principles and practices. Pearson. (Second edition), Prentice Hall, Inc.
3
[5] Miller, R. D., Ivanov, J., Xia, J., Peterie, S. L., & Sloan, S. L. (2010). Seismic investigations of subsidence hazards. In SEG Technical Program Expanded Abstracts 2010 (pp. 3769-3773). Society of Exploration Geophysicists.
4
[6] Sloan, S. D., Nolan, J. J., Broadfoot, S. W., McKenna, J. R., & Metheny, O. M. (2013). Using near-surface seismic refraction tomography and multichannel analysis of surface waves to detect shallow tunnels: A feasibility study. Journal of Applied Geophysics, 99, 60-65.
5
[7] Sloan, S. D., Peterie, S. L., Ivanov, J., Miller, R. D., McKenna, J. R., Bradford, J. H., & Holliger, K. (2010). Void detection using near-surface seismic methods. Advances in near-surface seismology and ground-penetrating radar: SEG Geophysical Developments Series, 15, 201-218.
6
[8] Sloan, S. D., Peterie, S. L., Miller, R. D., Ivanov, J., Schwenk, J. T., & McKenna, J. R. (2015). Detecting clandestine tunnels using near-surface seismic techniques. Geophysics, 80(5), EN127-EN135.
7
[9] Aminnedjad, B., & Butt, S. D. (2003). Imaging Abandoned Underground Mines and Assessing Geotechnical Hazards Research Project, Phase 1 Final Report – Assessment of State of the Art for Nondestructive Geophysical Imaging Technology, unpublished report.
8
[10] Ivanov, J., Miller, R. D., Park, C. B., & Ryden, N. (2003). Seismic search for underground anomalies. In: SEG Technical Program Expanded Abstracts 2003, (pp. 1223-1226), Society of Exploration Geophysicists.
9
[11] Steiakakis, E., Lazaropoulos, A., Vafidis, A., Agioutantis, Z., & Kritikakis, G. (2017). Determination of shear wave velocities in sediment deposits. International Journal of Geotechnical Engineering, 1-11.
10
[12] Nasseri-Moghaddam, A., Cascante, G., & Hutchinson, J. (2005). A new quantitative procedure to determine the location and embedment depth of a void using surface waves. Journal of Environmental & Engineering Geophysics, 10(1), 51-64.
11
[13] Nasseri-Moghaddam, A., Cascante, G., Phillips, C., & Hutchinson, D. J. (2007). Effects of underground cavities on Rayleigh waves—Field and numerical experiments. Soil dynamics and earthquake engineering, 27(4), 300-313.
12
[14] Xia, J., Nyquist, J. E., Xu, Y., Roth, M. J., & Miller, R. D. (2007). Feasibility of detecting near-surface feature with Rayleigh-wave diffraction. Journal of Applied Geophysics, 62(3), 244-253.
13
[15] Chai, H. Y., Phoon, K. K., Goh, S. H., & Wei, C. F. (2012). Some theoretical and numerical observations on scattering of Rayleigh waves in media containing shallow rectangular cavities. Journal of Applied Geophysics, 83, 107-119.
14
[16] Chai, H. Y., Goh, S. H., Phoon, K. K., Wei, C. F., & Zhang, D. J. (2014). Effects of source and cavity depths on wave fields in layered media. Journal of Applied Geophysics, 107, 163-170.
15
[17] Shi, P. (2015). Surface wave propagation effects on buried segmented pipelines. Journal of Rock Mechanics and Geotechnical Engineering, 7(4), 440-451.
16
[18] Shao, G. Z., Tsoflias, G. P., & Li, C. J. (2016). Detection of near-surface cavities by generalized S-transform of Rayleigh waves. Journal of Applied Geophysics, 129, 53-65.
17
[19] Park, C. B., Miller, R. D., Rydén, N., Xia, J., & Ivanov, J. (2005). Combined use of active and passive surface waves. Journal of Environmental and Engineering Geophysics, 10(3), 323-334.
18
[20] Morikawa, H., Sawada, S., & Akamatsu, J. (2004). A method to estimate phase velocities of Rayleigh waves using microseisms simultaneously observed at two sites. Bulletin of the Seismological Society of America, 94(3), 961-976.
19
[21] Castaings, M., Bacon, C., Hosten, B., & Predoi, M. V. (2004). Finite element predictions for the dynamic response of thermo-viscoelastic material structures. The Journal of the Acoustical Society of America, 115(3), 1125-1133.
20
[22] Hesse, D., & Cawley, P. (2006). Surface wave modes in rails. The Journal of the Acoustical Society of America, 120(2), 733-740.
21
[23] Luo, W., & Rose, J. L. (2007). Phased array focusing with guided waves in a viscoelastic coated hollow cylinder. The Journal of the Acoustical Society of America, 121(4), 1945-1955.
22
[24] Drozdz, M. B. (2008). Efficient finite element modelling of ultrasound waves in elastic media (Doctoral dissertation, Imperial College London). Imperial College London.
23
[25] Rajagopal, P., Drozdz, M., Skelton, E. A., Lowe, M. J., & Craster, R. V. (2012). On the use of absorbing layers to simulate the propagation of elastic waves in unbounded isotropic media using commercially available finite element packages. NDT & E International, 51, 30-40.
24
[26] Davoodi, M., Pourdeilami, A., Jahankhah, H., & Jafari, M. K. (2018). Application of perfectly matched layer to soil-foundation interaction analysis. Journal of Rock Mechanics and Geotechnical Engineering, 10(4), 753-768.
25
[27] Lin, S., & Ashlock, J. C. (2014). Multimode Rayleigh wave profiling by hybrid surface and borehole methods. Geophysical Journal International, 197(2), 1184-1195.
26
[28] Lin, S., & Ashlock, J. C. (2016). Surface-wave testing of soil sites using multichannel simulation with one-receiver. Soil Dynamics and Earthquake Engineering, 87, 82-92.
27
[29] Olsson, D. (2012). Numerical simulations of energy absorbing boundaries for elastic wave propagation in thick concrete structures subjected to impact loading. Thesis, Umeå University.
28
[30] Atkinson, J. H. (2000). Non-linear soil stiffness in routine design. Gèotechnique, 50(5), 487–508.
29
[31] Shirzad Shahrivar, M., Gholi Zadeh, A. (2017). Numerical investigation of soil and buried structures using finite element analysis. Journal of Structural and Construction Engineering, 3(4): 97-104. doi: 10.22065/jsce.2016.41241.
30
[32] Abbasi Karafshani, S., Ardakani, A. Yakhchalian, M. (2016). Comparison between the Effects of Near- and Far-Fault Ground Motions on the Seismic Response of a Soil-Pile-Structure System, Journal of Structural and Construction Engineering, 2(4), pp. 117-130.
31
[33] Schmelzbach, C., Jordi, C., Sollberger, D., Doetsch, J., Kaufmann, M., Meijer, W. Y. & Horstmeyer, H. (2015, June). Understanding the impact of karst on seismic wave propagation-a multi-method geophysical study. In 77th EAGE Conference and Exhibition-Workshops.
32
[34] Willem Ynze, Meijer. 2014. Numerical modeling for seismic exploration with karstic subsurface structures. Master of Science Thesis, Delft University of Technology, ETH Zurich, RWTH Aachen University
33
[35] Zeng, C., Xia, J., Miller, R. D., & Tsoflias, G. P. (2011). Application of the multiaxial perfectly matched layer (M-PML) to near-surface seismic modeling with Rayleigh waves. Geophysics, 76(3), T43-T52.
34
[36] Xu, Y., Xia, J., & Miller, R. D. (2007). Numerical investigation of implementation of air-earth boundary by acoustic-elastic boundary approach. Geophysics, 72(5), SM147-SM153.
35
[37] Goble, GC. Rausche, F. and Likinis, GE. (1980). the analysis of pile driving: a state-of-the-art. Proceedings of the 1st International Seminar on the Application of Stress-Wave Theory on Piles. Stockholm, Sweden, pp. 131–161.
36
[38] Khoubani, A., & Ahmadi, M. M. (2014). Numerical study of ground vibration due to impact pile driving. Proceedings of the Institution of Civil Engineers-Geotechnical Engineering, 167(1), 28-39.
37
[39] Serdaroglu, MS. (2010). Nonlinear Analysis of Pile Driving and Ground Vibrations in Saturated Cohesive Soils Using the Finite Element Method. PhD dissertation, University of Iowa, Iowa City, IA USA.
38
[40] Hunter, S. C. (1957). Energy absorbed by elastic waves during impact. Journal of the Mechanics and Physics of Solids, 5(3), 162-171.
39
[41] McLaskey, G. C., & Glaser, S. D. (2010). Hertzian impact: Experimental study of the force pulse and resulting stress waves. The Journal of the Acoustical Society of America, 128(3), 1087-1096.
40
[42] Lin, S. (2014). Advancements in active surface wave methods: modeling, testing, and inversion. PhD dissertation, Citeseer.
41
ORIGINAL_ARTICLE
بررسی و اولویت بندی موانع و چالش های مدیریت ریسک در پروژه های ساختمانی به روش مشارکت دولتی - خصوصی با استفاده از FMEA فازی
سرمایه گذاری در صنعت ساختمان با عدم قطعیت های فراوانی مواجه می باشد لذا انبوه سازی ساختمان و تامین هزینه های آن غالبا بر عهده بخش دولتی بوده است. یکی از راهکارهای تامین هزینه های انبوه سازی ساختمان مشارکت دولتی – خصوصی می باشد که در مسیر اجرای آن چالش ها و موانع فراوانی وجود دارد. لذا هدف این تحقیق، بررسی و اولویت بندی موانع و چالش های مدیریت ریسک در پروژه های ساختمانی به روش مشارکت دولتی - خصوصی می باشد. بدین منظور از روش پیمایشی و مطالعات کتابخانه ای استفاده شد. نمونه آماری این تحقیق، متشکل از افراد خبره شامل اعضای هیئت علمی دانشگاه و همچنین پیمانکاران، مشاوران و کافرمایان شاغل در یک پروژه ساختمانی مشارکت دولتی – خصوصی بود. پس از بررسی و تایید روایی و پایایی و گردآوری پرسشنامه های توزیع شده میان افراد نمونه آماری این تحقیق، داده ها با استفاده از روش FMEA فازی مورد تجزیه و تحلیل قرار گرفتند. نتایج حاصل از این تحقیق نشان داد که از مهمترین موانع و چالش های مدیریت ریسک در پروژه های ساختمانی با مشارکت دولتی – خصوصی میتوان به عدم آگاهی و درک ضعیف سیاستمداران و تصمیم گیرندگان از مشارکت دولتی – خصوصی، سخت گیر و زمانبر بودن تملک بر اراضی مورد نیاز برای احداث پروژه های مشارکت دولتی – خصوصی و عدم تمایل بانک ها به منظور سرمایه گذاری در ترتیبات مشارکت دولتی - خصوصی اشاره نمود.
https://www.jsce.ir/article_88297_2bc573a57c9d88478a3936a741d92f6b.pdf
2021-04-21
301
318
10.22065/jsce.2019.178993.1826
کلمات کلیدی: ریسک
مدیریت ریسک
ساختمان سازی
مشارکت دولتی – خصوصی
FMEA فازی
علی
پروری
ali.parvari@iau.ac.ir
1
گروه عمران، دانشکده فنی مهندسی، دانشگاه آزاد اسلامی، واحد خمین، خمین ایران
LEAD_AUTHOR
بهزاد
رستمی
behzadrostami7@yahoo.com
2
گروه مهندسی عمران، دانشکده مهندسی عمران، دانشگاه آزاد اسلامی واحد خمین، خمین، ایران
AUTHOR
[1] Badri, A., Nadeau, S., & Gbodossou, A. (2011). Proposal of a risk-factor-based analytical approach for integrating occupational health and safety into project risk evaluation. Accident Analysis and Prevention, 48, 223-234.
1
[2] Jin, X.H. (2011). Model for efficient risk allocation in privately financed public infrastructure projects using neuro-fuzzy techniques. Journal of Construction Engineering Management, 137 (11), 1003- 1014.
2
[3] World Bank. (2003). Bank Group Private Sector Development Strategy Implementation Progress Report. Washington, D.C.
3
[4] Babaie, A., Hosseini, M., & Babaie, R. (2015). Promoting safety level of construction projects through risk management. National Conference on Architecture, Engineering and Urban Development, Mazandaran.
4
[5] Smith, N.J. (2003). Appraisal, risk and uncertainty. Thomas Telford Ltd, UK, London.
5
[6] Williams, T., (1995). A Classified Bibliography of Recent Research Relating to Project Risk Management, European. Journal of Operation Research, 85, 18-38.
6
[7] Khaksar, M., Shafeie, R., & Allah Veisi, B. (2008). Identification of origins of risk in construction projects, and method of their management (case study). Scientific-Research Journal of Farasooye Modiriat, 2 (7), 139-160.
7
[8] Brax, S.A., & Jonsson, K. (2008). Developing integrated solution offerings for remote diagnostics: a comparative case study of two manufacturers. Integr. Solution Offerings, 29 (5), 539–560.
8
[9] Bamford, J.D., Gomes-Casseres, B., & Robinson, M.S., (2003). Mastering Alliance Strategy: A Comprehensive Guide to Design, Management and Organization. Wiley, San Francisco, CA.
9
[10] Tam, W.Y.V., & Shen, L.Y. (2012). Risk management for contractors in marine projects. Organization, Technology and Management in Construction: An International Journal, 4 (1), 403–410.
10
[11] Mark, W., Cohen, P.E., & Glen, R.P. (2004). Project risk identification and management. AACE International Transaction. INT.01, 1-5.
11
[12] Chia, S.E.) 2006(. Risk assessment framework for project management. IEEE, 376–379
12
[13] Deputy Office of Strategic Planning and Supervision. (2008). Risk management in projects. Journal No. 659, Deputy Office of Technical Affairs, Formulation Criteria, and Reduction of Risk-taking resulted from Earthquake, Tehran.
13
[14] Nieto-Morote, A., & Ruz-Vila, A. (2011). A fuzzy approach to construction project risk assessment. International Journal of Project Management, 29, 220–231.
14
[15] Cooper, D., Grey, S., Raymond, G., & Walker, P. )2005(. Project Risk Management Guidelines: Managing Risk in Large Projects and Complex Procurements. Chichester: John Wiley & Sons, Ltd.
15
[16] Winch, G. (2002). Managing construction projects, an information processing approach. Oxford: Blackwell Publishing.
16
[17] Latham, M. (1994). Constructing the team. HMSO London.
17
[18] Ng, S.T., Wong, Y. M.W. & Wong, J. M.W. (2012). Factors influencing the success of PPP at feasibility stage – A tripartite comparison study in Hong Kong. Habitat International, 36 (4), 423-432.
18
[19] Grimsey, D., & Lewis, M.K. (2004). Public private partnerships: the worldwide Revolution in infrastructure provision and project finance. UK: Edward Elgar Publishing Limited.
19
[20] Umar, A.A., Idrus, A., & Khamidi, M.F. (2011). Barriers to the use of public-private partnerships for provision of public infrastructure in developing countries: review. National Postgraduate Conference. IEEE Conference Publications.
20
[21] Liu, T., & Wilkinson, S. (2011). Adopting innovative procurement techniques: Obstacles and drivers for adopting public private partnerships in New Zealand. Construction Innovation: Information, Process, and Management. 11(4), 452–469.
21
[22] Economic and Social Commissi on for Asia and the Pacific (ESCAP). (2011). A guidebook on public-Private partnership in infrastructure. United Nations.
22
[23] Danaie Fard, H., Delkhah, J., & Kiaiee, P. (2017). Identifying and prioritizing obstacles ahead of public-private sector partnership development. Scientific-Research Journal of Business Management, 29, 33-49.
23
[24] Sohrabi R., & Rostami, A. (2017). Prioritizing challenges exisiting in partnership contracts of public-private sector in infrastructure projects. Scientific-Research Journal of Management Optimization (Behbood Modiriat), 11 (3), 139-160.
24
[25] Makki Abadi, S.R., Behnia, C., & Akbari, A. (2014). Identification and evaluation of critical risks in HSR projects trough public-private partnership in developing countries. Journal of Structural and Construction Engineering, 1 (1), 5-18.
25
[26] Ardeshir, A., AmirI, M., & Mohajeri, M. (2013). Safety risk evaluation in mass housing projects through combination of fuzzy FMEA, fuzzy FTA, and AHP-DEA. Scientific-Research Journal of Iran Occupational Health, 10 (6), 78-91.
26
[27] Rezaeenour, J, & Mousavi Saleh, M. (2018). Evaluation and ranking of public-private partnership risk factors in water supply projects using FMEA and Fuzzy Synthetic Evaluation methods Acase study of Qom. Journal of Iran water resources research, 13 (4), 100-117.
27
[28] Keers, B.B.M., & Fenema, P.C.V. (2018). Managing risks in public-private partnership formation projects. International Journal of Project Management, 36, 861– 875.
28
[29] Cui, C, Liu, Y, Hope, A, Wang, J. (2018). Review of studies on the public–private partnerships (PPP) for infrastructure projects. International Journal of Project Management, https://doi.org/10.1016/j.ijproman.2018.03.004.
29
[30] Qazi, A., Quigley, J., Dickson, A., & Kirytopoulos, K. (2016). Project complexity and risk management (ProCRiM): Towards modelling project complexity driven risk paths in construction projects. International Journal of Project Management, 34, 1183 – 1198.
30
[31] Zarezadeh, H, & Barkhordari Bbafqi, M.A. (2016). Risk assessment of public private partnership contract in highway projects: A comparison between simple and fuzzy methods. Journal of administrative Management, education and traning, 12(3), 481-492.
31
[32] Press D. Guidelines for Failure Mode and Effects Analysis (FMEA), for Automotive, Aerospace, and General Manufacturing Industries: CRC Press, 2003.
32
[33] Kumru, M., & Kumru, P. (2013). Fuzzy FMEA application to improve purchasing process in a public hospital. Applied Soft Computing, 13(1), 721–733.
33
[34] Abdelgawad, M., & Fayek, A.R. (2010). Risk in the management construction industry using combined fuzzy FMEA and fuzzy AHP. Journal of Construction Engineering and Managemen, 136 (9), 1028-1036, ASCE.
34
[35] Kia, M. (2010). Fuzzy logic in MATLAB. First issue, Kian Rayaneh Sabz Publication.
35
[36] Abdollah Zadeh, G., & Rastgoo, S. (2012). Risk evaluation in bridge construction projects through fuzzy fault tree analysis. National Conference on Civil Engineering and Architecture with an Emphasis on Sustainable Development, Khavaran Higher Education Institute, Mashhad.
36
[37] Keikha, R., & Hossein Abadi, H. (2013). Reviewing problems and obstacles ahead of effective organization of public-private sector partnership projects, and provision of Solutions. Seventh National Congress on Civil Engineering, Zahedan, University of Sistan and Baluchestan.
37