@article { author = {azimzadeh, ali and Keyvani, Abdullah and Hoveidae, Nader}, title = {Numerical investigation of the effect of joint core details on the performance of reinforced concrete column to steel beam connection in corner columns}, journal = {Journal of Structural and Construction Engineering}, volume = {6}, number = {4}, pages = {5-22}, year = {2019}, publisher = {Iranian Society of Structural Engineering (ISSE)}, issn = {2476-3977}, eissn = {2538-2616}, doi = {10.22065/jsce.2018.99622.1341}, abstract = {The past severe earthquakes around the world have shown that the beam to column connection is prone to failure. Therefore, significant provisions should be considered in the design of the connection. RCS moment-resisting frame systems, consisting of Reinforced Concrete (RC) columns and Steel (S) beams, take advantage of the inherent stiffness and damping, as well as low-cost of concrete, the lightweight and construction efficiency of structural steel. Since two types of materials including steel and concrete are used in a RCS system, the detail of the connection plays a significant role on the overall performance of the system. In general, there are two types of RCS connections, column through type & beam through type. The main objective of this study is to investigate the effect of parallel and diagonal stiffeners on stress-strain propagation and concrete damage in column through type RCS connections. For this purpose, RCS connections with different joint details were modeled and analyzed in ABAQUS. Finite element analyses results showed that parallel stiffeners are more capable to provide confinement in comparison to the diagonal types. However, the performance of diagonal stiffeners in terms of strength and plastic hinge formation in the joint is better than parallel stiffeners. Increase of stiffener thickness causes to improve the performance of joint core and decreases its damage level. Furthermore, increasing in cover-plate thickness improves the performance of connections in terms of of strength and plastic hinge formation.}, keywords = {Joint core,Parallel stiffener,Diagonal stiffener,Stress,Damage,RCS connection}, title_fa = {بررسی عددی تأثیر جزئیات چشمه اتصال در عملکرد اتصالات تیر فولادی به ستون بتنی در ستونهای گوشه}, abstract_fa = {مشاهده ساختمان‌های آسیب‌دیده در برابر زلزله نشان داده است که تحت بارهای لرزه‌ای، اتصالات تیر به ستون آسیب‌پذیرترین المان سازه‌ای بوده و نسبت به سایر اعضای سازه‌ای به توجهات خاص در طرح و اجرا نیاز دارد. از آنجایی که در سازه‌ های با اتصالات تیر فولادی – ستون بتن آرمه1 (RCS) از دو نوع مصالح مختلف در چشمه اتصالات استفاده می شود، لذا جزئیات اتصال این نوع سازه ها می‌تواند نقشی اساسی در عملکرد کلی اتصال داشته باشد. بطور کلی اتصالات سازه‌های RCS به دو دسته تقسیم می شوند: اتصال نوع تیر پیوسته و اتصال نوع ستون پیوسته. هدف از این مقاله تمرکز برروی چشمه اتصالات RCS از نوع ستون پیوسته و مقایسه عملکرد و تأثیر سخت کننده‌های موازی و قطری با یکدیگر درخصوص نحوه توزیع تنش-کرنش و خرابی بتن ناشی از بارگذاری چرخه ای در چشمه اتصال می‌باشد. برای این منظور اتصالات RCS ستون گوشه با جزئیات مختلف در چشمه اتصال، با استفاده از نرم افزار آباکوس2 مدل‌سازی شده و مورد تحلیل قرار گرفتند. نتایج حاصل از تحلیل المان محدود نشان داد که به‌طور کلی سخت‌کننده‌های موازی اثر محصور کنندگی بهتری از خود نشان می‌دهند ،لکن عملکرد سخت‌کننده‌های قطری از لحاظ مقاومت و شکل‌گیری مفصل پلاستیک در اتصال بهتر می‌باشد. همچنین نتایج نشان داد که افزایش ضخامت سخت‌کننده باعث بهبود رفتار چشمه اتصال شده و اندیس خرابی آن را کاهش می‌دهد . همچنین افزایش ضخامت کاورپلیت عملکرد اتصالات را از لحاظ مقاومت و شکل‌گیری مفصل پلاستیک بهبود می‌بخشد.}, keywords_fa = {چشمه اتصال,سخت‌کننده موازی,سخت‌کننده قطری,تنش,خرابی,اتصال RCS}, url = {https://www.jsce.ir/article_61644.html}, eprint = {https://www.jsce.ir/article_61644_fecdfe3d6d6e456ba0ddae2c29e0eb31.pdf} } @article { author = {Fadaei, Farnaz and Hassani, Nemat and Saffari, Hamid}, title = {Soil longitudinal variation effects on seismic behavior of buried pipelines}, journal = {Journal of Structural and Construction Engineering}, volume = {6}, number = {4}, pages = {23-37}, year = {2019}, publisher = {Iranian Society of Structural Engineering (ISSE)}, issn = {2476-3977}, eissn = {2538-2616}, doi = {10.22065/jsce.2018.108454.1391}, abstract = {The purpose of this study is to investigate the behavior of continuous pipeline passing through two different layers of soil with different levels of resistance under displacement time-histories of the same earthquake. The values of stress and displacement are studied for different angles between pipe and interface of soil layers. To this end, pipe and the surrounding soil are modeled using shell and solid elements, respectively, in ABAQUS Software. Stress and displacement values are calculated along the intersection and for different values of intersection angle between soil layer and pipeline and different values of Young's modulus of the soils. These evaluations indicate that, the maximum stress along the pipeline occurs at the node in certain distance before the interface in the harder soil. Moreover, with increasing the angle, the resulting displacement increases, and the value of stress increases with angles up to 30˚, beyond which angle it decreases. Also, a decrease in the ratio of Young's modulus increases the stress both before and after the interface. Significant changes are observed in displacement and stress along the pipeline with changing the pipe thickness, so that a decrease in the pipe thickness in the studied model from 20 to 15 mm (33% reduction) results in some 15% increase in the stress. Soft soil (two-layered soft soil) increases pipe displacement and response capacity in every condition.}, keywords = {Buried pipeline,earthquake,Displacement time-history record,Pipeline intersection,Finite element method}, title_fa = {تأثیر تغییرات طولی ساختار خاک در رفتار لرزه ای لوله های مدفون}, abstract_fa = {چکیده: هدف از این مقاله بررسی رفتار خطوط لوله پیوسته گذر کننده از دو خاک با جنس و سختی متفاوت تحت اثر تغییر مکان های زمانی یک زلزله یکسان می باشد. شاخص های تنش و جابجایی به ازای زاویه های مختلف بین خط لوله و مرز بین دو لایه ی خاک بررسی شده است. بدین منظور از نرم افزار آباکوس استفاده گردید و لوله با المان پوسته ای و خاک اطراف آن به صورت توده پیوسته مدل سازی شد. مقدار تنش و جابجایی در طول تقاطع و به ازای زاویه ها ی تقاطع مختلف خاک و لوله و نسبت مدول یانگ متفاوت خاک ها به دست آورده شد. نتایج نشان می دهند که بیش ترین تنش در طول لوله در گره به فاصله مشخصی قبل از مرز و در خاک سخت تر ایجاد می شود. هم چنین با افزایش زاویه تقاطع لوله با مرز بین دو لایه، مقدار جابجایی بیشتر شده و مقدار تنش تا زاویه 30 درجه افزایش و سپس کاهش می یابد. کاهش نسبت مدول یانگ نیز باعث افزایش تنش در قبل و بعد از محل تقاطع می گردد. با تغییر ضخامت لوله، جابجایی و تنش در لوله و خاک لایه ای اطراف آن دستخوش تغییرات قابل ملاحظه ای می گردد به‌طوری‌که با کاهش ضخامت لوله از 20 به 15 میلی متر (کاهش 33%) تنش حدوداً 15 درصد افزایش می یابد. شرایط خاک نرم (خاک دو لایه با جنس خاک نرم) در هر شرایطی منجر به افزایش ظرفیت تغییر شکل و پاسخ لوله می گردد.}, keywords_fa = {لوله مدفون,زلزله,رکورد تاریخچه زمانی تغییر مکان,تقاطع لوله,تحلیل اجزای محدود}, url = {https://www.jsce.ir/article_61777.html}, eprint = {https://www.jsce.ir/article_61777_f8db12262b8f1bd3d2834e2cce440bb5.pdf} } @article { author = {Shahrabi, Behnam and Hemmati, Seyed Jalal}, title = {Numerical analysis of rolled beam deformations subjected to heat straightening}, journal = {Journal of Structural and Construction Engineering}, volume = {6}, number = {4}, pages = {38-54}, year = {2019}, publisher = {Iranian Society of Structural Engineering (ISSE)}, issn = {2476-3977}, eissn = {2538-2616}, doi = {10.22065/jsce.2018.108868.1411}, abstract = {Restoration of the steel structures by heat straightening process has a long history, but national studies in this field have not been reported yet. The physical nature of this process is thermo mechanical, and the most of conducted studies have included the empirical investigation of angular distortions and mechanical deformations of structures and the restoration with the help of accelerators such as hydraulic jacks. In the present study, the numerical heat transfer and structural analysis of the process were carried out on an I-shaped cross section steel beam without application of external load. Oxy acetylene torch was considered as the heat source, and the Gaussian normal distribution model was used to model the input heat flux from flame to the beam surface. Three dimensional transient heat transfer and thermo elastic plastic deformations were analysed by finite element method in ANSYSTM software, and the results of thermo elastic plastic deformations were evaluated based on the amount of plastic rotation in the beam. Also role of the effective parameters such as supporting conditions, torch speed in different heating zones, heating dimensions and the path of torch movement on upper wing of the beam were studied. The results of numerical simulations carried out were in reasonable agreement with existing empirical data and showed the contribution of thermal deformation in the final deformations of the beam due to the non-application of external force.}, keywords = {Heat straightening process,thermal-structural analysis,plastic rotation,Vee and strip Heating,flame heating}, title_fa = {تحلیل عددی تغییر شکل تیرهای نورد شده در معرض صاف‌کاری حرارتی}, abstract_fa = {ترمیم سازه‌های فولادی به روش صا‌ف‌کاری حرارتی قدمت طولانی دارد اما مطالعاتی در این زمینه در داخل کشور گزارش نشده است. ماهیت فیزیکی این فرآیند، حرارتی- مکانیکی است و اکثر مطالعات صورت ‌‌گرفته نیز شامل بررسی تجربی اعوجاج‌ها و تغییر شکل‌های مکانیکی سازه‌ها و ترمیم به کمک ابزارهای تسریع کننده مانند جک‌‌های هیدرولیک بوده است. در این تحقیق، به تحلیل حرارتی و سازه‌ای این فرآیند روی یک تیر فولادی با مقطع I- شکل بدون اعمال بار خارجی پرداخته شد. مشعل اکسی استیلن به عنوان منبع حرارت، مد نظر بوده و از مدل شار حرارت نرمال گوسی برای مدل‌سازی شار حرارت ورودی از شعله به تیر استفاده شد. تحلیل انتقال حرارت گذرای سه بعدی و تغییر شکل‌های سازه‌ای به روش المان محدود در نرم ‌افزار ANSYS، انجام گرفت و نتایج حاصل از تغییر شکل‌های حرارتی بر اساس میزان دوران پلاستیک در تیر بررسی شدند. همچنین نقش متغیرهای موثری مانند شرایط تکیه‌گاهی، سرعت مشعل در نواحی مختلف گرمایش، ابعاد منطقه گرم‌کاری و مسیر حرکت مشعل روی بال فوقانی تیر مورد مطالعه قرار گرفتند. نتایج شبیه‌‌سازی‌های عددی انجام گرفته در مقایسه با داده‌های تجربی موجود، همخوانی کیفی معقولی داشتند و به واسطه عدم اعمال نیروی خارجی، سهم حرارت در میزان تغییر شکل نهایی تیر تبیین گردید.}, keywords_fa = {فرآیند صاف‌کاری حرارتی,تحلیل حرارتی- سازه‌ای,دوران پلاستیک,گرمایش مثلثی و نواری,گرمایش شعله‌ای}, url = {https://www.jsce.ir/article_62636.html}, eprint = {https://www.jsce.ir/article_62636_0023e6832c264b63f79dc29e978e511e.pdf} } @article { author = {Esmailzadeh Shahri, Reza and Karamodin, Abbas}, title = {Numerical Study of Structure-Soil-Structure Interaction Effects on Deflection Amplification Factor and Correction for Special Steel Moment Frames}, journal = {Journal of Structural and Construction Engineering}, volume = {6}, number = {4}, pages = {55-70}, year = {2019}, publisher = {Iranian Society of Structural Engineering (ISSE)}, issn = {2476-3977}, eissn = {2538-2616}, doi = {10.22065/jsce.2018.113313.1424}, abstract = {Considering the importance of the deflection amplification factor ,Cd, in the structural design and the lack of consideration of the structure-soil-structure interaction effects on structural response, this paper has investigated the effects of the most important parameters affecting this factor in the structure-soil-structure systems. Key parameters are period of main (T1) and adjacent (T2) structures, distance between the structures (d) and type of soil. The purpose of this study is to correct the Cd coefficient in steel moment frames under the influence of structural-soil-structure interaction effect. For this aim, 6 structures of 2 to 15 story based on two types of clay soil in a three distances of zero, 10 and 25 meters using direct method is modelled and analyzed with nonlinear time history method. According to the results, most of the story drifts is concentrated at the first story due to soft base. The minimum ratio of first story drift with respect to the fix-base, is 1. 1 and the maximum is 3.61. Increasing T1 And T2, the value of this ratio is increased. For the main structures with T1 in the range of 0.7 to 1.5 times the soil period, the structural drift is intensified. Finally, using the results of this study and regression analysis, a correlation coefficient for the Cd is presented based on the spectral response of the structural drift. Based on the obtained relationship, story drifts, especially at first story, should be increased for the design of the structures .}, keywords = {Structure-soil-structure interaction,Soil-structure interaction,Deflection amplification factor,Structural drift,Soft story}, title_fa = {مطالعه عددی تاثیرات اندرکنش سازه-خاک-سازه بر ضریب بزرگنمایی تغییرمکان و اصلاح آن برای قاب خمشی فولادی ویژه}, abstract_fa = {با توجه به اهمیت ضریب بزرگنمایی تغییرمکان Cd در طراحی سازه‌ها و عدم درنظر گرفتن اثرات اندرکنش سازه-خاک-سازه در پاسخ سازه‌ها، این مقاله اثرات مهم‌ترین پارامترهای تأثیرگذار بر این ضریب، در سامانه سازه-خاک-سازه را بررسی کرده است. پارامترهای کلیدی شامل دوره تناوب سازه اصلی (T1) و مجاور (T2)، فاصله سازه‌ها (d) و نوع خاک هستند. هدف از این پژوهش، اصلاح ضریب Cd در قاب‌های فولادی ویژه تحت اثر اندرکنش سازه-خاک-سازه، بدون مدل‌سازی سازه مجاور است. برای این منظور 6 سازه 2 تا 15طبقه واقع بر دو نوع خاک رسی به صورت دوتایی در سه فاصله صفر، 10 و 25 متری با استفاده از روش مستقیم به‌صورت غیرخطی مدل و با استفاده از روش تاریخچه زمانی غیرخطی تحلیل شده‌اند. بر اساس نتایج این کار، تکیه‌گاه نرم منجر به ایجاد طبقه نرم به‌دلیل افزایش شدید دریفت طبقه اول نسبت به حالت تکیه‌گاه ثابت می‌شود که حداقل این نسبت 1/1 و حداکثر آن 61/3 است؛ به‌طوری که با افزایش T1 و T2 مقدار این نسبت بیشتر می‌گردد. از طرفی برای سازه‌های اصلی با T1 در محدوده 7/0 تا 5/1 برابر دوره تناوب خاک، دریفت سازه دچار تشدید می‌شود. در نهایت با استفاده از نتایج کار و تحلیل رگرسیون، بر مبنای طیف پاسخ دریفت سازه‌ها روابطی جهت اصلاح ضریب Cd ارائه شده است. بر اساس رابطه به‌دست‌آمده، برای طراحی سازه بایستی مقادیر دریفت به‌خصوص دریفت طبقه اول افزایش یابد.}, keywords_fa = {اندرکنش سازه-خاک-سازه,اندرکنش خاک-سازه,ضریب بزرگنمایی تغییرمکان,دریفت سازه,طبقه نرم}, url = {https://www.jsce.ir/article_62637.html}, eprint = {https://www.jsce.ir/article_62637_a40fe924aceda2a121f12a6c8077196d.pdf} } @article { author = {bahirai, mohammad and Gerami, Mohsen}, title = {Investigation and comparison of some techniques in asymmetrically retrofitting of steel frame connections}, journal = {Journal of Structural and Construction Engineering}, volume = {6}, number = {4}, pages = {71-94}, year = {2019}, publisher = {Iranian Society of Structural Engineering (ISSE)}, issn = {2476-3977}, eissn = {2538-2616}, doi = {10.22065/jsce.2018.109293.1399}, abstract = {The presence of concrete slab in steel framing frame structures always makes retrofitting problems difficult. On the other hand, most of damages reported from Northridge earthquake (1994) has focused on the bottom flange of the beam. Therefore, in order to reduce the cost of retrofit, this operation can be done only at the bottom flange of the beam. In other words, by defining and applying a ductile fuse in the beam, by weakening the bottom flange of the bottom, it is possible to reduce the concentration of tension in the near-weld regions in connection and fracture failure in these areas. In this paper, a steel frame connection was analyzed numerically and after ensuring the modeling accuracy, it was under rehabilitation. Retrofit techniques have been made on the bottom flange of the beam. Two general "cut-off" and "heat" methods were considered to weaken the beam. In this research, incomplete penetration of the weld was placed in the bottom flange connection to the column as a deficiency in the joint. The modeling results showed that the connection with incomplete weld, underwent 4/4%, suffering a deflection in the weld area in the flange. In the specimens which were retrofitted asymmetrically, the possibility of brittle fracture in the weld region was decreased due to relocation of the plastic hinge in the weakened area of the beam. In the method of reducing the bottom flange, lateral buckling led to sudden decrease in flexural strength at 2.5 % inter story drift. In the heat-induction method accompanied with steel annealing, the out of buckling occurred at 5% drift. The retrofitted connection with this method showed a post elastic displacements of 3% and could be expected to be suitable for special moment frames.}, keywords = {moment frame connection,seismic retrofit,heat treated beam section (HBS),reduced beam section (RBS),Finite element method}, title_fa = {بررسی ومقایسه چند روش در بهسازی نامتقارن اتصالات قاب خمشی فولادی}, abstract_fa = {در مقاله حاضر روش جدیدی به عنوان روش حرارتی به منظور بهسازی اتصالات قاب خمشی فولادی بررسی شده است. در روش حرارتی به آنیل کردن فولاد در ناحیه نزدیک به بر ستون مبادرت میشود. به این ترتیب انتظار میرود مفصل پلاستیک به ناحیه‌ای به فاصله 0.5d تا 1.5d (d عمق تیر) در تیر انتقال یابد. روش انجام تحقیق بدین گونه است که ابتدا اتصالی که مدل آزمایشگاهی آن در دسترس است در نرم افزار اجزای محدود مدلسازی میشود و پس از صحت سنجی و اطمینان از دقت مدل اجزای محدود، به استفاده از روش حرارتی در حوزه بهسازی مبادرت میشود. نمونه‌ها با فرض عدم اطمینان از کیفیت جوش در نظر گرفته شده‌اند به این ترتیب که نقصی در جوش که شامل مقاومت کمتر در بال پایین است قرار داده شده است. علت این امر این است که عموماً کیفیت جوش در بال بالا به دلیل کنترل راحت‌تر بیشتر میباشد. سپس با استفاده از روشهای تضعیفی این اتصال بهسازی شده است. این روشها شامل کاهش مقطع بال پایین، حرارت بال پایین، کاهش مقطع جان در ناحیه نزدیک بال و یک روش ترکیبی بوده است.نتایج مدلسازی نشان دادند که روش کاهش مقطع منجر به کمانش خارج از صفحه شده و علی رغم اقناع شرط شکلپذیری آیین‌نامه، روش مناسبی برای بهسازی اتصالات نیست. روش حرارتی عملکرد مناسبی را تا حدود 5 درصد رادیان به وجود می‌اورد. استفاده از لچکی به تعداد 1 یا 2 در بال پایین به انتقال مفصل پلاستیک کمک می‌نماید اما به کمانش خارج از صفحه در این حالت باید توجه ویژه نمود.}, keywords_fa = {قاب خمشی فولادی,بهسازی لرزه‌ای,اتصال با مقطع کاهش یافته,اتصال حرارت دیده,روش اجزای محدود}, url = {https://www.jsce.ir/article_62638.html}, eprint = {https://www.jsce.ir/article_62638_2f772211870b5d832e0fe87cf9fecf89.pdf} } @article { author = {zandi, yousef and Alayi, mehdi}, title = {Effect of Comparison of Ardabil Pozzuoli Cement and Type 2 Sufyan Cement Compressive Strength Viewpoints and Improvement Solutions}, journal = {Journal of Structural and Construction Engineering}, volume = {6}, number = {4}, pages = {95-110}, year = {2019}, publisher = {Iranian Society of Structural Engineering (ISSE)}, issn = {2476-3977}, eissn = {2538-2616}, doi = {10.22065/jsce.2018.117984.1454}, abstract = {In this research, we investigate the possibility and possibility of replacing Ardabil type 2 Pozzuoli cement instead of Sufian type 2 cements from the standpoint of compressive strength in dam construction projects. Experiment on samples shows the possibility of just using Ardebil's pozzolan cement is not possible in concrete projects .In order to achieve this, we need to think about the measures. In order to achieve this, we need to think about the measures.Among the mechanical properties of the compressive strength of the concrete made with cement type 2 pesulani of Ardebil, there is a severe drop.The most important priorities for using additives are the availability of materials along with economic discussions. For this purpose, four cement substitute additives were used in this study: stone powder, sand, microsilica, and fly ash. The results of the experiments show that the fly ash in the long run increases the compressive strength of the concrete and in the first days reduces the compressive strength. Microsilica for 8% and 11% increases resistance initially, but for replacement percentage 5, it reduces the compressive strength of the concrete. The fine sand also causes a slight reduction in compressive strength; ultimately, the replacement of stones in the long run will increase the compressive strength of the concrete}, keywords = {Ardebil Pozzuoli cement,Type 2 Sufyan cement,Fly ash,Microsilica,Stone powder}, title_fa = {بررسی مقایسه‌ای سیمان پوزولانی اردبیل و سیمان تیپ 2 صوفیان از دیدگاه مقاومت فشاری و ارائه راهکار بهبود}, abstract_fa = {در این پژوهش به بررسی چگونگی و امکان‌سنجی جایگزینی سیمان تیپ 2 پوزولانی اردبیل به جای سیمان تیپ 2 صوفیان از دیدگاه مقاومت فشاری در پروژه‌های سدسازی پرداخته شده است. آزمایش بر روی نمونه‌های شاهد نشان می‌دهد که امکان استفاده از سیمان پوزولانی اردبیل به تنهایی در پروژه‌های بتن‌ریزی سازه‌ای امکان‌پذیر نمی‌باشد و برای نیل به این هدف نیازمند اندیشیدن تمهیداتی هستیم که در میان مشخصات مکانیکی مقاومت فشاری بتن های ساخته شده با سیمان تیپ 2 پزولانی اردبیل شاهد افت شدیدی می باشد.از مهمترین اولویت های استفاده از مواد افزودنی در دسترس بودن مصالح در کنار بحث های اقتصادی است . بدین منظور در این پژوهش از چهار ماده افزودنی جایگزین سیمان استفاده شده است که عبارتند از: پودر سنگ، نرمه ماسه، میکروسیلیس و خاکستر بادی. نتایج آزمایش‌ها نشان می‌دهد که خاکستر بادی در دراز مدت مقاومت فشاری بتن را افزایش داده و در روزهای نخست مقاومت فشاری را کاهش می‌دهد. میکروسیلیس برای 8 و 11% از ابتدا مقاومت را افزایش می‌دهد ولی برای درصد جایگزینی 5 منجر به کاهش مقاومت فشاری بتن می‌گردد. نرمه ماسه نیز باعث کاهش جزئی مقاومت فشاری می‌گردد؛ و در نهایت جایگزینی پودر سنگ در دراز مدت منجر به افزایش مقاومت فشاری بتن می‌گردد.}, keywords_fa = {سیمان پوزولانی اردبیل,سیمان تیپ 2 صوفیان,خاکستر بادی,میکروسیلیس,پودر سنگ}, url = {https://www.jsce.ir/article_62639.html}, eprint = {https://www.jsce.ir/article_62639_3460c9b8b4d04dc1edc4dcf237d615cd.pdf} } @article { author = {Hatefi, Seyed Morteza and Mohseni, Hassan}, title = {Evaluating and prioritizing the risks of BOT projects using structural equations and integrated model of fuzzy AHP and fuzzy TOPSIS}, journal = {Journal of Structural and Construction Engineering}, volume = {6}, number = {4}, pages = {111-130}, year = {2019}, publisher = {Iranian Society of Structural Engineering (ISSE)}, issn = {2476-3977}, eissn = {2538-2616}, doi = {10.22065/jsce.2018.112728.1419}, abstract = {The private sector has an important role on the development of cities, and governments are encouraging this sector to implement civilian projects. The BOT approach is one of the ways that increases private sector participation in government infrastructure development. Today, paying attention to the financing of urban projects and new financing approaches, including the BOT approach, is necessity in most of the major cities, especially in Tehran. But it is necessary to use the BOT method to address and understand all the dimensions and issues behind the implementation of this method. In many cases, failure to complete the projects in due time is due to the lack of proper management of the project, which results from a lack of understanding of the risks involved in these projects. Therefore, assessment and prioritization of risks in BOT projects, especially when the number of risk factors increases, is considered as an important part of the complex risk management process. In this paper, the method of structural equations and integrated model of fuzzy AHP and fuzzy TOPSIS are used to evaluate and prioritize the risks in Tehran Municipality's development projects that are implemented in the form of BOT contract method. Structural equations are used to measure the validity of identified risks. The fuzzy AHP method is used to determine the weight of the risk assessment criteria and the fuzzy TOPSIS method is utilized to evaluate and prioritize the risks of BOT projects. The results indicate that the risk of commodity price fluctuations, the risk of rising inflation, the risk of exchange rate fluctuations, and the risk of non-application of techniques and project management knowledge are the most important risks in BOT projects.}, keywords = {Risk Management,Risk Assessment,BOT contracts,fuzzy AHP,Fuzzy TOPSIS}, title_fa = {ارزیابی و اولویت‌بندی ریسک‌های پروژه‌های BOT با استفاده از معادلات ساختاری و مدل یکپارچه فرآیند تحلیل سلسله مراتبی فازی و TOPSIS فازی}, abstract_fa = {بخش خصوصی اهمیت بسزایی در توسعه و عمران شهرها داشته و دولت‌ها مشوق این بخش در اجرای پروژه‌های عمرانی هستند. روش BOT از روش‌هایی است که مشارکت بخش خصوصی را در توسعه زیربنایی دولت افزایش می‌دهد. امروزه توجه به تامین مالی پروژه‌های شهری و رویکردهای جدید تامین مالی از جمله روش BOT در اکثر شهرهای بزرگ کشور و خصوصا شهر تهران یک ضرورت بشمار می‌رود. اما لازمه استفاده از روش BOT، پرداختن و شناخت همه ابعاد و مسائل پیش‌روی این روش اجرایی است. در بسیاری موارد عدم انجام پروژه‌ها در موعد مقرر، به علت عدم مدیریت صحیح پروژه بوده که آن هم از عدم شناخت کافی نسبت به ریسک‌های موجود در این پروژه‌ها ناشی می‌شود. بنابراین ارزیابی و اولویت‌بندی ریسک‌ها در پروژه‌هایی که به روش BOT انجام می شوند، به ویژه زمانی که تعداد عوامل ریسک‌زا افزایش می‌یابد، به عنوان بخشی مهم از فرآیند پیچیده مدیریت ریسک محسوب می‌شود. در این تحقیق از روش معادلات ساختاری و مدل یکپارچه فرایند تحلیل سلسله مراتبی فازی و روش تاپسیس فازی برای ارزیابی و اولویت‌بندی ریسک‌های موجود در پروژه‌های عمرانی شهرداری تهران که در قالب روش قراردادی BOT اجرا می شوند، پرداخته می شود. از معادلات ساختاری برای سنجش اعتبار ریسک های شناسایی شده استفاده می شود. از روش AHP فازی برای تعیین وزن معیارهای ارزیابی ریسک و از روش تاپسیس فازی برای ارزیابی و اولویت‌بندی ریسک‌های پروژه های BOT استفاده می‌شود. نتایج نشان می‌دهد که ریسک نوسانات قیمت مواد اولیه، ریسک افزایش نرخ تورم، ریسک نوسانات نرخ ارز و ریسک عدم کاربرد تکنیک‌ها و دانش مدیریت پروژه به عنوان مهم‌ترین ریسک‌ها در پروژه‌های BOT می باشند.}, keywords_fa = {مدیریت ریسک,ارزیابی ریسک,قراردادهای بی‌او‌تی,تحلیل سلسله مراتبی فازی,تاپسیس فازی}, url = {https://www.jsce.ir/article_63029.html}, eprint = {https://www.jsce.ir/article_63029_ef8c53eae092e283d9c239036729f444.pdf} } @article { author = {Ghannadiasl, Amin and esrafiili, hosein and Rahman Shokrgozar, Hamed}, title = {Seismic Performance of Concentrically Steel Braced Frames with Eccentric Gusset Plates}, journal = {Journal of Structural and Construction Engineering}, volume = {6}, number = {4}, pages = {131-142}, year = {2019}, publisher = {Iranian Society of Structural Engineering (ISSE)}, issn = {2476-3977}, eissn = {2538-2616}, doi = {10.22065/jsce.2018.109307.1401}, abstract = {Different types of the lateral-load resisting systems to deal with lateral forces entering the building are used in buildings such as the concentrically braced frames (CBFs). The application of the concentrically braced frames is welcomed due to its lateral stiffness and other benefits. In accordance with the regulations, the brace axis should meet at the intersection point of the column centroid and the beam centroid axes. In many cases, the eccentric gusset plates at the connection of the brace and the beam are observed in the concentrically braced frames. Therefore, in this paper, the effect of the eccentricities at the connection of braces on the behavior of the CBFs including the in-plane and out-plane eccentricities of the gusset plate by finite element method is investigated in order to determine the optimal performance of the structure when the if the failure of the regulations observes. Hence, 11 models are used to determine the margin of confidence for non-observance of the rules of the regulations in the frames with Eccentric Gusset Plates using the Abacus software. The results show that the effect of the in-plane eccentricities is far more unfavorable than the out-plane eccentricities and there is little margin of confidence for non-observance of the rules of the regulations.}, keywords = {Seismic Performance,Concentrically Steel Braced Frames,Eccentric Gusset Plates,Gusset Plates,Nonlinear analysis}, title_fa = {عملکرد لرزه ای قاب‌های مهاربندی شده همگرا با خروج از مرکزیت ورق اتصال بادبند}, abstract_fa = {در ساختمان‌ ها از سیستم‌ های باربر جانبی مختلفی برای مقابله با نیروی‌ های جانبی وارد بر ساختمان استفاده می‌شود که از آن جمله می‌توان به مهاربندی‌ های همگرا اشاره کرد. کاربرد قا‌‌ب‌ های مهاربندی همگرای فولادی به دلیل سختی جانبی و سایر مزایای آن با استقبال روبرو است. مطابق آیین‌نامه‌ ها باید راستای محور ورق اتصالات از تلاقی تار خنثی تیر و ستون عبور کند. اما در بسیاری، موارد خروج از مرکزیت صفحه در محل اتصال ورق بادبند به تیر در قاب های مهاربندی شده همگرا مشاهده شده است. از این رو در این مقاله به بررسی تاثیر خروج از مرکزیت بر رفتار قاب مهاربندی شده همگرا شامل خروج از مرکزیت داخل و خارج صفحه ورق اتصال به روش اجزای محدود پرداخته شده است تا مشخص گردد که عدم رعایت ضوابط آیین‌نامه‌ ای تا چه میزان در عملکرد سازه خلل وارد می‌کند. به این منظور، یازده مدل برای تعیین حاشیه اطمینان برای عدم رعایت قوانین آیین‌نامه در قاب‌های دارای خروج از مرکزیت با استفاده از نرم‌افزار آباکوس مورد استفاده قرار گرفت. نتایج نشان داده که تاثیر خروج از مرکزیت داخل صفحه به مراتب نامطلوب‌تر از خروج از مرکزیت خارج صفحه بوده و حاشیه اطمینان کمی برای عدم رعایت قوانین آیین‌نامه وجود دارد.}, keywords_fa = {قاب مهاربندی شده همگرا,ورق اتصال,تحلیل غیر خطی,خروج از مرکزیت افقی,خروج از مرکزیت افقی قائم}, url = {https://www.jsce.ir/article_63030.html}, eprint = {https://www.jsce.ir/article_63030_4051a0958d0f84b5972df9acdbb76a3a.pdf} } @article { author = {Tajdaran, Ahmad and SADDAGH, MOHAMMADHASSAN}, title = {Effect of Geometric Parameters on Elastoplastic Buckling of Ground Cylindrical Steel Tanks with Regard to the Fluid and Structure Interaction}, journal = {Journal of Structural and Construction Engineering}, volume = {6}, number = {4}, pages = {143-161}, year = {2019}, publisher = {Iranian Society of Structural Engineering (ISSE)}, issn = {2476-3977}, eissn = {2538-2616}, doi = {10.22065/jsce.2018.105006.1379}, abstract = {Todays due to expansion of population and industry, the collection and storage of liquids has been paid attention more and more. Saving oil and chemical liquids require great care to maintain it. One of the most important and commonly structures for storing liquids is steel cylindrical above ground tanks. On the other hand, due to damage of tanks in past earthquakes, they persuade scientists to better understand the seismic behavior.As a consequence, this research has been studied examines the phenomenon of buckling under Bam, Golbaf, Firuzabad, Bojnurd, Manjil, Tabas and Sarein eartquakes with regard to the fluid and structure interaction. Tanks were selected with ratio of 0.5, 1.0, 1.5 and 2.0 with fixed and variable thickness in full mode. These Cases were analyzed with non-linear time history analysis by ABAQUS Software.Finally, Compare the results with American petroleum institute regulation (API), Iranian seismic design code for oil industries and forces show, both height and diameter increase to growth the risk of Elastoplastic buckling and also by increasing the height to diameter ratio reduces the risk of Elastoplastic Buckling. The amount of this damage has declined by increasing shell thickness and in the same vein designing these structure by define standards is not safe method.}, keywords = {Cylindrical Steel Tanks,Finite Elements Method,Elastoplastic Buckling,Nonlinear dynamic analysis,Fluid Structure Interaction}, title_fa = {تاثیر پارامتر های هندسی بر کمانش الاستوپلاستیک مخازن فلزی استوانه‌ایی زمینی با درنظر گرفتن اندرکنش سازه و سیال}, abstract_fa = {امروزه با گسترش جمعیت و صنعت، جمع آوری و ذخیره سازی مایعات بیش از پیش مورد توجه قرار گرفته است. دخیره مایعات نفتی و شیمیایی ازجمله مواردی هستند که نگهداری آنها نیاز به دقت فراوانی دارد. یکی از سازه‌های مهم و پرکاربرد جهت ذخیره سازی مایعات در صنعت نفت مخازن فلزی استوانه‌ایی روزمینی می‌باشد. اما با توجه به آسیب‌های عمده‌ایی که بر اینگونه مخازن در زلزله‌های گذشته وارد آمده؛ محققین را وادار به درک و پیش‌بینی بهتری از رفتار لرزه‌ایی آنها نموده است. از این رو دراین پژوهش به بررسی یکی از آسیب‌های محتمل برمخازن (پدیده کمانش) تحت بارهای لرزه‌ای؛ زلزله های بم، گلباف، فیروزآباد، بجنورد، منجیل، طبس و سرعین با در نظرگرفتن اندرکنش سازه و سیال پرداخته شده است. مخازن مورد مطالعه با نسبت های ارتفاع به قطر 5/0 ، 0/1 ، 5/1 و 2 با ضخامت پوسته ثابت و متغییر، درحالت پر، انتخاب شده و روش تحلیل، آنالیز دینامیکی تاریخچه زمانی غیرخطی بوده که توسط نرم‌افزار اجزاء محدود آباکوس انجام شده است. مقایسه نتایج با آیین نامه API-650، آیین نامه لرزه‌ایی سازه های صنعت نفت ایران و نیروهای بدست آمده ازتحلیل نشان می‌دهند افزایش قطر و ارتفاع، هر دو پارامتر موثری درافزایش خطر کمانش الاستوپلاستیک می‌باشند. همچنین افزایش نسبت ارتفاع به قطر باعث کاهش خطر کمانش الاستوپلاستیک شده و با افزایش مقدار ضخامت پوسته احتمال رخ دادن پدیده کمانش الاستوپلاستیک بسیار کم می‌شود و طراحی مخازن با آیین نامه های مذکور روش مطمئنی برای جلوگیری از کمانش نمی‌باشد}, keywords_fa = {مخازن فولادی استوانه‌ایی,روش اجزاء محدود,کمانش الاستوپلاستیک,تحلیل دینامیکی غیرخطی,اندرکنش سازه و سیال}, url = {https://www.jsce.ir/article_63031.html}, eprint = {https://www.jsce.ir/article_63031_1099857155b53cb7f36adee096b63a37.pdf} } @article { author = {قیاسی, واحد and Hajisafari, Meysam and Saboteh, Ehsan}, title = {Compare the axial bearing capacity piles cylindrical, tapered and semi-tapered in the sand by finite element method}, journal = {Journal of Structural and Construction Engineering}, volume = {6}, number = {4}, pages = {162-175}, year = {2019}, publisher = {Iranian Society of Structural Engineering (ISSE)}, issn = {2476-3977}, eissn = {2538-2616}, doi = {10.22065/jsce.2018.102011.1356}, abstract = {Use piles with variable section can improve the bearing capacity of the piles, due to the larger cross-section upper part of piles. The function and easy implementation of semi-tapered piles that only the top half is in the form of a cone are better than the previous one. The purpose of this paper is determine the bearing capacity increase tapered and semi-tapered tapered piles and comparing with the cylindrical piles in the same volume condition. The modeling of this research paper is based on finite element method (Plaxis 2D software) of numerical analysis for changing the angle and tapered height of mentioned piles, axial bearing capacity of these piles in sand is estimated. Linear elastic behavior is assumed for pile and the hardening soil criterion is considered for soil. The analysis was performed for piles with different lengths. Load carrying capacity and settlement at the given particular loading were examined. Influences of stresses are also discussed with respect to change in taper angle. The results show that settlement decreases with increase in taper angle. Load-displacement curve shows that the tapered pile can take more loads compared to cylindrical pile when the taper angle load- settlement curve of piles compare showed that tapered piles bearing capacity and especially semi-tapered piles greater than cylindrical piles. It was also observed that the increase in capacity, more piles occur with short length.}, keywords = {Taper piles,Semi-taper piles,Piles bearing capacity,Taper angle,Numerical modeling}, title_fa = {مقایسه ظرفیت باربری محوری شمع‌های استوانه‌ای، مخروطی و نیمه‌مخروطی در ماسه به روش اجزای محدود}, abstract_fa = {با تغییر هندسه مقطع شمع یا مخروطی کردن شمع‌ها، می‌توان بدون افزایش حجم مصالح مصرفی ، به ظرفیت باربری بیشتری دست یافت. شمع‌های مخروطی که دارای سطح مقطع بزرگتری نسبت به قسمت انتهایی شمع هستند، از نظر ظرفیت باربری، عملکرد لرزه‌ای و همچنین توزیع بهتر مصالح در طول شمع بسیار کارآمدتر از شمع‌های استوانه‌ای می‌باشند. شمع‌های نیمه‌مخروطی که فقط قسمت بالایی آن به صورت مخروطی می‌باشد، از عملکرد و سهولت اجرایی بهتری نسبت به دو نوع قبلی( مخروطی و استوانه ای) برخوردار هستند هدف از انجام این تحقیق تعیین میزان افزایش ظرفیت باربری شمع‌های مخروطی و نیمه‌مخروطی نسبت به شمع‌های استوانه‌ای هم‌حجم می باشد.. در این پژوهش آنالیز عددی به روش اجزای محدود (نرم‌افزار Plaxis 2D) به منظور بررسی اثر تغییر زاویه نوک شمع و ارتفاع مخروطی شمع در خصوص تعیین ظرفیت باربری محوری آنها نسبت به شمع‌های استوانه‌ای هم‌حجم در ماسه پرداخته شده است. همچنین ظرفیت باربری شمع‌های نیمه‌مخروطی که از نظر محققان دور مانده است نیز در این تحقیق مورد بررسی قرار ‌گرفته است. آنالیزها برای شمع‌های با طول مختلف انجام شده است. مقایسه مقادیر ظرفیت باربری نهایی به دست آمده از نمودار بار- نشست شمع‌ها، حاکی از ظرفیت باربری بیشتر شمع های مخروطی و به خصوص نیمه‌مخروطی نسبت به شمع‌های استوانه‌ای داشته است. همچنین مشاهده شد که افزایش ظرفیت باربری، بیشتر در شمع‌های با طول کوتاه اتفاق می‌افتد.}, keywords_fa = {شمع مخروطی,شمع نیمه‌مخروطی,ظرفیت باربری شمع,زاویه شمع,مدل سازی عددی}, url = {https://www.jsce.ir/article_63032.html}, eprint = {https://www.jsce.ir/article_63032_3511bee87949410810a898da1d4bfb7e.pdf} } @article { author = {Katebi, Ali and Almassian, Fariborz and Homami, Peyman}, title = {Multi Mode Resource Constraint Construction Project Scheduling Problem (MRCPSP) Considering the Uncertainty in the Activities Duration and Delays}, journal = {Journal of Structural and Construction Engineering}, volume = {6}, number = {4}, pages = {176-198}, year = {2019}, publisher = {Iranian Society of Structural Engineering (ISSE)}, issn = {2476-3977}, eissn = {2538-2616}, doi = {10.22065/jsce.2018.108681.1396}, abstract = {Choosing construction methods and how resources are allocated are important in the project control. The multi-mode resource constrained project scheduling problem (MRCPSP) is a significant subject in project management. The development of the above model for construction projects is an important issue because of uncertainty. Fuzzy logic has been used to display the uncertainty in the duration of activities and the delay between them. This paper examines this problem and schedules project with providing an intelligent algorithm combining fuzzy sets and genetic algorithms (GAs). The Fuzzy MRCPSP problem can be considered as the scheduling of a set of activities with the aim of finding an activity operation mode and the activity operation priority; so that the resource constraints (renewable resources and non-renewable resources) as well as the precedence constraints are met simultaneously and the time for completion of the project is minimal. In the first step, the above problem is modeled mathematically, and then the model is coded using GA-based algorithm in Matlab software and finally the model is solved. The results of the implementation of this algorithm on the standard instances of the PSPLIB site, in comparison with the GAMS software, indicate the successful performance of the combined GA algorithm with fuzzy sets. The approach used in this research can be easily used by project managers. This prevents human errors caused by people who are responsible for controlling the project at resource leveling phase and is a way to the optimized project scheduling.}, keywords = {Resource constraints construction projects fuzzy scheduling,fuzzy delays,multi-mode activities,minimization of project completion time,GA algorithm}, title_fa = {زمان‌بندی پروژه‌های ساخت با منابع محدود (MRCPSP) با در نظر گرفتن عدم قطعیت در مدت فعالیت‌ها و تأخیرات}, abstract_fa = {انتخاب روش‌های ساخت، نحوه تخصیص منابع اهمیت زیادی در کنترل پروژه‌ دارد. مسئله زمان‌بندی پروژه با منابع محدود در چندین حالت اجرایی (MRCPSP) موضوعی مطرح در مدیریت پروژه است. توسعه مدل فوق برای پروژه‌های ساخت، به‌دلیل وجود فضای غیرقطعی، امری مهم به‌نظر می‌رسد. برای نمایش عدم قطعیت مدت‌زمان انجام فعالیت‌ها و تأخیر بین آن‌ها، از منطق فازی استفاده شده‌است. در این مقاله به بررسی این مسئله پرداخته و با ارائه یک الگوریتم هوشمند ترکیب‌شده از مجموعه‌های فازی و الگوریتم ژنتیک (GA)، زمان‌بندی صورت گرفته‌است. مسئله MRCPSP فازی را می‌توان زمان‌بندی مجموعه‌ای از فعالیت‌ها باهدف یافتن یک روش اجرایی و توالی زمانی مناسب برای انجام فعالیت‌ها در نظر گرفت؛ به‌طوری‌که محدودیت‌های منابع (منابع تجدید پذیر و منابع تجدید ناپذیر) و نیز محدودیت‌های پیش‌نیازی به‌طور هم‌زمان ارضا گردند و زمان تکمیل پروژه کمینه شود. در گام اول مسئله مذکور مدل‌سازی ریاضی می‌شود و سپس، اقدام به کدنویسی مدل مسئله با استفاده از الگوریتم فراابتکاری GA در نرم‌افزار Matlab و حل مدل ریاضی مسئله می‌شود. نتایج حاصل از پیاده‌سازی این الگوریتم بر روی مسائل استاندارد سایت PSPLIB، در مقایسه با نرم‌افزار GAMS، حاکی از عملکرد موفق الگوریتم GA تلفیق‌شده با مجموعه‌های فازی است. رویکرد بکار گرفته‌شده در این پژوهش می‌تواند به‌سادگی قابل‌استفاده توسط مدیران و برنامه‌ریزان پروژه باشد. این امر موجب جلوگیری از خطاهای انسانی مسئول کنترل پروژه در تسطیح منابع می‌شود و راهی به‌سوی زمان‌بندی بهینه پروژه است.}, keywords_fa = {زمان‌بندی فازی پروژه ساخت با محدودیت منابع,فعالیت‌های چند حالته,تأخیرات فازی,کمینه کردن زمان تکمیل پروژه,الگوریتم‌ فراابتکاری GA}, url = {https://www.jsce.ir/article_63246.html}, eprint = {https://www.jsce.ir/article_63246_a5b1bdb758e0db5b31540cfc1a0c9b38.pdf} } @article { author = {Sademomtazi, Ali and Ghodousian, Oveys}, title = {Comparison of pull-off, push-out and splitting prism tests for assessment of bonding between fiber-reinforced self-compacting concrete as a repair layer and concrete substrate.}, journal = {Journal of Structural and Construction Engineering}, volume = {6}, number = {4}, pages = {199-212}, year = {2019}, publisher = {Iranian Society of Structural Engineering (ISSE)}, issn = {2476-3977}, eissn = {2538-2616}, doi = {10.22065/jsce.2018.106322.1388}, abstract = {Considering using self-compacting concrete – because of no need to vibration and flow ability of this kind of concrete under its weight – under challenging situation for consolidation, it would be a very suitable option for using as repair layer in repairing and retrofitting of concrete structures. In this issue, quality of bonding between the repair layer and concrete substrate is one of the most important factors in durability and suitable performance of repairing works. On this base, in this research, some effective factors on bonding between two layers i.e. volume paste, water to cementitious materials and fiber dosages and their effects on rheological properties of repair self-compacting concrete firstly, on mechanical properties of it including compressive strength, tensile strength, modulus of elasticity and shrinkage secondly and on bonding quality between the self-compacting repair layer and concrete substrate finally have been assessed. For assessment of bonding between two concrete layers, three methods including pull-off, push-out and splitting prism have been used. The results show that because of highly effects of shrinkage on bonding, the factors that reduce shrinkage, i.e. volume paste, water to cementitious materials and fiber dosages will increase the bonding of the two concrete layers. In this issue, the exact effect of each of these parameters on bonding between the two concrete layers and the optimum value of them have been assessed. Also, the correlation between all three methods of assessment of bonding between self-compacting concrete as a repair layer and concrete substrate and preciseness of the methods have been found.}, keywords = {pull-off,push-out,splitting prism,bonding,Self-Compacting Concrete}, title_fa = {مقایسه روش های پول آف، پوش اوت و منشور شکافت برای تعیین چسبندگی بتن خودتراکم الیافی به عنوان لایه تعمیری بر بستر بتنی.}, abstract_fa = {با توجه به امکان استفاده از بتن خودتراکم - به علت عدم نیاز این نوع بتن به تراکم و جاری شدن تحت وزن خود - در شرایطی که تراکم به سختی قابل انجام است، این نوع بتن گزینه بسیار مناسبی برای استفاده به عنوان لایه تعمیری در سازه های بتنی و ترمیم و مرمت آنها است. در این میان کیفیت چسبندگی این لایه به بتن بستر از مهمترین عوامل دوام و عملکرد مناسب عملیات تعمیر انجام شده می باشد. بر این اساس در این مطالعه به بررسی چند عامل تاثیر گذار بر چسبندگی بین دولایه یعنی حجم خمیره، نسبت آب به مصالح سیمانی و مقدار الیاف و تاثیر آنها اولا بر ویژگی های رئولوژیکی بتن خود تراکم تعمیری و دوم بر ویژگی های مکانیکی این بتن شامل مقاومت فشاری، مقاومت کششی، مدول الاستیسیته و جمع شدگی آن و سوم بر کیفیت چسبندگی بین این بتن و بتن بستر پرداخته شده است. به منظور تعیین چسبندگی بین دو لایه بتنی از روش های پول- آف، پوش- اوت و منشور شکافت بهره گرفته شده است. نتایج نشان دادند که به دلیل تاثیر زیاد مقدار جمع شدگی بر چسبندگی دو لایه، عوامل کاهش جمع شدگی یعنی کاهش حجم خمیره، کاهش نسبت آب به مصالح سیمانی و وجود الیاف، منجر به افزایش چسبندگی می شوند. در این ارتباط مقدار دقیق تاثیر هر یک از این پارامترها بر مقدار چسبندگی دو لایه و نیز مقدار بهینه هر یک تعیین گردید. همچنین ارتباط بین روش های مختلف تعیین چسبندگی دو لایه و مقدار کارامدی و دقت هر یک به دست آمد.}, keywords_fa = {پول آف,پوش اوت,منشور شکافت,چسبندگی,بتن خودتراکم}, url = {https://www.jsce.ir/article_63566.html}, eprint = {https://www.jsce.ir/article_63566_13504fd33d7107654077420ae099e93f.pdf} } @article { author = {Radkia, Sahar and Rahnavard, Rohola and Abbas Gandomkar, Farhad}, title = {Evaluation of the effect of different seismic isolators on the behavior of asymmetric steel sliding structures}, journal = {Journal of Structural and Construction Engineering}, volume = {6}, number = {4}, pages = {213-230}, year = {2019}, publisher = {Iranian Society of Structural Engineering (ISSE)}, issn = {2476-3977}, eissn = {2538-2616}, doi = {10.22065/jsce.2018.114089.1428}, abstract = {Isolation of buildings from earth vibrations is a new method that has been considered in the last few decades and is the only way to reduce simultaneously the inter-story displacement and acceleration of stories. In this method, increasing the period of rotation and damping of the structure at the separated level, the energy from the earthquake force to the structure decreases. Furthermore, recent earthquakes, including the Bam earthquake, have horizontal and vertical components, which resulted in the destruction of more structures, depending on the time of the start of the vertical or horizontal components or their combination. This issue highlights the importance of examining the vertical component of the earthquake in addition to the horizontal component. According to the mentioned cases, the main objective of this research is to investigate the behavior of asymmetric sliding structures with different separators under the horizontal component and the combination of horizontal and vertical components of the earthquake, taking into account the effects of soil and structure interaction. For this purpose, structures of 1, 5, and 10 stories irregular building(irregular amount of 40%) with seismic separators R-FBI, LRB and P-F on soil type IV are considered. In order to obtain the results of the research, the numerical method of finite element method has been used with modelling of materials in nonlinear area and performing explicit dynamic analysis. The results of the study showed that with increasing number of stories, the seismic separation function of R-FBI is better than other LRB and P-F separators. Also, the results of this study show that the simultaneous effect of horizontal and vertical components on structures 1 and 10 is remarkable.}, keywords = {sliding structure,isolator,seismic analysis,Steel moment frame,Finite element method}, title_fa = {ارزیابی اثر انواع جداگرهای لرزه ای بر رفتار سازه لغزشی نامتقارن فولادی}, abstract_fa = {جداسازی ساختمان‌ها از ارتعاشات زمین روش جدیدی است که در چند دهه اخیر مورد توجه زیادی قرار گرفته و تنها راه عملی کاهش هم‌زمان تغییر‌مکان بین طبقه‌ای و شتاب‌های طبقات می‌باشد. در این روش با افزایش زمان تناوب و میرایی سازه در تراز جداسازی شده، انرژی ناشی از نیروی زلزله به سازه کاهش می‌یابد. از طرفی زلزله‌های اخیر از جمله زلزله مخرب بم دارای مولفه‌های افقی و عمودی بوده است که بسته به زمان شروع مولفه‌های قائم یا افقی و یا ترکیب آن‌ها، تخریب بیشتر سازه‌ها را در پی داشته است. این موضوع اهمیت بررسی مولفه قائم زلزله را علاوه بر مولفه افقی نمایان می سازد. با توجه به موارد عنوان شده، هدف اصلی این تحقیق بررسی رفتار سازه‌های لغزشی نامتقارن با جداگر‌های مختلف تحت اثر مولفه‌ی افقی و ترکیب مولفه‌های افقی و قائم زلزله با در نظر گرفتن اثرات اندرکنش خاک و سازه می باشد. جهت دستیابی به هدف اصلی تحقیق، ریز اهدافی مانند بررسی تاثیر مشخصات جداسازها و تاثیر ترکیب مولفه‌های افقی و قائم زلزله بر پاسخ لرزه ای سازه مورد مطالعه مورد توجه قرار گرفتند. برای این منظور، سازه‌های یک، پنج و ده طبقه نامنظم (میزان نامنظمی 40%) با جداگرهای لرزه‌ای R-FBI، LRB و P-F واقع بر روی خاک تیپ IV در نظر گرفته شده است جهت حصول نتایج تحقیق از روش عددی اجزا محدود با مدل‌سازی مصالح در ناحیه غیرخطی و انجام آنالیز دینامیکی صریح بهره گرفته شده است. نتایج تحقیق نشان دادند که با افزایش تعداد طبقات عملکرد جداگر لرزه‌ای R-FBI بهتر از سایر جداگر‌های LRB و P-F است. هم‌چنین نتایج این تحقیق نشان می‌دهد که اثر هم‌زمان مولفه‌های افقی و قائم بر سازه 1 و 10 طبقه چشم‌گیر است.}, keywords_fa = {سازه لغزشی,جداگر,آنالیز لرزه ای,قاب خمشی فولادی,روش اجزای محدود}, url = {https://www.jsce.ir/article_63630.html}, eprint = {https://www.jsce.ir/article_63630_589155f95e6fa8bf4316e641363acf4b.pdf} } @article { author = {pachideh, ghasem and Gholhaki, Madjid and moshtagh, amin}, title = {The effect of quantity and type of fibers and recycled metal springs on concrete properties}, journal = {Journal of Structural and Construction Engineering}, volume = {6}, number = {4}, pages = {231-247}, year = {2019}, publisher = {Iranian Society of Structural Engineering (ISSE)}, issn = {2476-3977}, eissn = {2538-2616}, doi = {10.22065/jsce.2018.113952.1426}, abstract = {The use of fibers or recycled materials in concrete will results in improving the strength, plasticity and durability of concrete. Therefore, one of the suggestions to improve the mechanical properties of concrete is the use of fibers as well as alternative materials such as recycled steel springs. In this paper, we investigate the performance of concretes containing steel and polypropylene fibers and recycled metal springs using 0.2, 0.4, 0.6 and 0.8 percent volumetric percentages. For this purpose, a number of cylindrical and prismatic samples at the age of 28 days were tested for compressive, tensile and flexural strength tests. It should be noted that the steel fibers used have a length and diameter of 50 and 0.8 mm, polypropylene fiber has 12 mm length, as well as a metal spring with a wire diameter of 0.8 mm, a length of 25 mm and a hole diameter of 8 mm. The results indicate that the use of recycled metal springs in concrete has a better performance than other fibers in the control of cracks caused by tension. Also, in low percentages, the use of springs has improved the mechanical properties of concrete. Also, polypropylene fibers and metal springs increase the flexural strength of concrete up to 2 times, which for the use of steel fibers this amounts to 13 times. So, with better recognition and changes in the type and characteristics of the spring, better resistance can be achieved.}, keywords = {Concrete,Steel Fiber,Polypropylene fiber,Recycled Steel Springs,Mechanical properties}, title_fa = {تأثیر مقدار و نوع الیاف و فنر فلزی بازیافتی بر خصوصیات بتن معمولی}, abstract_fa = {بتن به عنوان یک ماده ی ساختمانی عملکردی ضعیفی در کشش داشته و این مسأله باعث وقوع ترک و خزش می شود. با گذشت زمان و افزایش تنش ها، ترک ها زیاد شده و در عمق بتن نفوذ می کنند. به همین جهت از الیاف فولادی جهت جلوگیری از رشد بیش از حد ترک ها استفاده می شود. استفاده از الیاف یا مواد بازیافتی در بتن، باعث بهبود مقاومت، شکل پذیری و دوام بتن می شود. لذا یکی از پیشنهادات بمنظور بهبود خواص مکانیکی بتن، استفاده از الیاف و مصالح جایگزین نظیر فنر فلزی بازیافتی است. در این مقاله به مطالعه ی آزمایشگاهی عملکرد بتن های حاوی الیاف فولادی و پلی پروپیلن و فنرهای فلزی بازیافتی با بکار بردن درصدهای حجمی 2/0، 4/0، 6/0 و 8/0 درصد پرداخته شد. بدین منظور تعدادی نمونه ی استوانه ای و منشوری جهت انجام آزمایشات مقاومت فشاری، کششی و خمشی ساخته و در سن 28 روزه مورد آزمایش قرار گرفت. نتایج حاکی از آن است که استفاده از فنر فلزی بازیافتی در بتن، عملکرد مطلوب تری نسبت به سایر الیاف ها در کنترل ترک های ناشی از کشش دارد. همچنین در درصدهای کم، استفاده از فنر بهبود بیشتری در خصوصیات مکانیکی بتن دارد. همچنین الیاف پلی پروپیلن و فنر فلزی تا 2 برابر طاقت خمشی بتن را افزایش داده، که این مقدار برای استفاده از الیاف فولادی به 13 برابر می رسد.}, keywords_fa = {بتن,الیاف فولادی,الیاف پلی پروپیلن,فنر فلزی بازیافتی,مشخصات مکانیکی}, url = {https://www.jsce.ir/article_63863.html}, eprint = {https://www.jsce.ir/article_63863_dff4a4be2f8d3982acec498d9d1c50f4.pdf} }